Teledyne TIENet 301 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 30

Teledyne TIENet 301 Скачать руководство пользователя страница 21

TIENet

®

301 pH/Temperature Device

Section 2 Installation and Setup for Signature

2-9

Figure 2-9 Menu Tree: 301 Configuration

Configure Measurements

TIENet Setup (Smart Sensor)

•

Perform Scan

•

Configure Measurements

XXX Parameter

XXX Parameter

XXX Parameter

Select Operation

1. Hardware Setup

2. Configure

3. Administration

4. Home

1 - XXX

Configure Measurements

TIENet Configuration

The sensors are being

configured. Please wait...

TIENet Setup (Smart Sensor)

The sensors have been configured.

301 pH

301 Temperature

2 - 301

Hardware Setup

1. Smart Sensor Setup (TIENet)

2. SDI-12 Setup

3. MODBUS Input Setup

4. MODBUS Output Setup

5. Modem Setup

Press Enter for a list of
sensors. Scroll to the 301
and press Enter to select.

Scroll with arrow keys to
highlight / select / deselect
any displayed parameter or
edit its name.

Press NEXT to confirm configuration.
There may be a slight delay.

With initial connection, begin
by performing a hardware
scan to add the 301.

«
...
19
20
21
22
23
...
»

Содержание TIENet 301































Отзывы:

Нет отзывов