manualshive.com logo in svg

Teledyne LeCroy T3DSO2000A Series, Руководство пользователя

Поделиться
Скачать
Teledyne LeCroy T3DSO2000A Series Скачать руководство пользователя страница 53

T3DSO2000A Manual. Page 49

In addition to manually specifying a frame, history mode supports autoplay.

Press the

softkey to replay the waveform from the current frame to the first.

Press the

softkey to stop replay.

Press the

softkey to replay the waveform from the current frame to the last.

Touch the Interval Time area to control the speed of automatic play. In the process of
automatic play, the list will automatically scroll to the current frame.

14.4 Zoom

The T3DSO2000A supports waveform zoom in the horizontal
direction. Press down the horizontal knob on the front panel to turn
on the zoom function.

When the Zoom function is on, the waveform area is divided into
upper and lower parts. The area of about 1/3 height above is the
main window, and the area of about 2/3 height below is the zoom
window. Touch a window to activate it.

The area not covered by the grey background in the main waveform area is the
region to be zoomed in (zoom area). When the zoom window is activated, the zoom
area can be expanded or compressed by rotating the horizontal and vertical scale
knob. Rotating the horizontal and vertical position knob to move the position of the
region. When the main window is activated, the scale knobs and position knobs are
used to change the scale and delay/offset of the main window. The operations above
can also be performed by different gestures. Below is the example of changing the
setting on horizontal directions by gestures:

www.

.com

[email protected]

1.800.561.8187

Содержание LeCroy T3DSO2000A Series










































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды