manualshive.com logo in svg

Teledyne LeCroy T3DSO2000A Series, Руководство пользователя

Поделиться
Скачать
Teledyne LeCroy T3DSO2000A Series Скачать руководство пользователя страница 196

T3DSO2000A Manual. Page 192

Press the "Single" button to switch to red and green display mode. Observe whether
there is any color distortion, bad pixel or scratch on the screen.

Press the "Run/Stop" button to exit the screen test mode.

Keyboard Test

The keyboard test is used to check whether the oscilloscope front panel buttons or
knobs are responsive or sensitive. Perform Utility>Do Self-Test>Keyboard Test to
recall the following interface:

Knob test: Turn each knob clockwise, counter-clockwise, and press down. Observe
whether the value on the corresponding knob (default 0) on the screen increases or
decreases in real-time and whether the knob lights up when it is pressed.

Button test: Press each button and check whether the corresponding button icon on
the screen lights up in real-time.

Press the "Run/Stop" button three times to exit the keyboard test.

LED Test

The LED test is used to check whether the button backlight on the front panel is
functional. Operate Utility>Do Self-Test >LED Test to recall the following interface:

www.

.com

[email protected]

1.800.561.8187

Содержание LeCroy T3DSO2000A Series










































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды