56
Piranha 2 User’s Manual
03-032-00493-14
Teledyne DALSA
Line Dropout, Bright Lines, or Incorrect Line Rate
Verify that the frequ ency of the internal syn c is set correctly, or w hen the cam era is set to
external sync th at the EXSYN C signal su p p lied to the cam era d oes not exceed the
camera’s maximum specified line rate.
Noisy Output
Check you r p ow er su p p ly voltage ou tp u ts for noise. N oise p resent on these lines can
resu lt in p oor vid eo qu ality. Low qu ality or non -tw isted p air cable can also ad d noise to
the vid eo ou tp u t.
Dark Patches
If d ark p atches ap p ear in you r ou tp u t the op tics p ath m ay have becom e contam inated .
Clean you r lenses an d sen sor w ind ow s w ith extrem e care.
1.
Take stand ard ESD p recau tions.
2.
Wear latex gloves or finger cots
3.
Blow off d u st u sing a filtered blow bottle or d ry, filtered com p ressed air.
4.
Fold a p iece of op tical len s cleaning tissu e (ap p rox. 3" x 5") to m ake a squ are p ad th at
is ap p roxim ately one finger -w id th
5.
Moisten the p ad on one ed ge w ith 2-3 d rop s of clean solvent—either alcohol or
acetone. Do not satu rate the entire p ad w ith solvent.
6.
Wip e across the length of the w ind ow in one d irection w ith the m oistened end first,
follow ed by the rest of the p ad . The d ry p art of the p ad sh ou ld follow the m oistened
end . The goal is to p revent solvent from evap orating from the w ind ow su rface, as this
w ill end u p leaving resid u e and streakin g behind .
7.
Rep eat step s 2-4 u sing a clean tissu e u ntil the entire w ind ow has been cleaned .
8.
Blow off any ad hering fibers or p articles u sing d ry, filtered com p ressed air.
Stuck Bits
If d ata bits seem to be stu ck or d o not ch ange, check that the cam era is not satu rated by
p reventing light from entering. To verify the d ata p ath in tegrity, check the levels of the 2
test p attern p ixels (first 2 p ixels follow ing the last En d -of-line p ixel. You m ay need to tu rn
the End -of-line sequ ence ―on ‖ by sen d ing the com m and
els 1
). Any d eviation from a
consistent valu e of these p ixels (170DN / 85DN ) cou ld be an ind ication of the follow in g:
shorted bits
stu ck bits
d igital noise p icku p on the I/ O cable
op en connection.
To activate the test p attern, u se the com m an d
svm 2
. Use the test p attern to verify the
p rop er tim ing an d connections betw een the cam era an d fram e grabber.
To receive a com p lete line of raw vid eo d ata (w ith ou t d igital p rocessing or test p attern)
throu gh the RS232 p ort, u se the com m and
gl
. The retu rn ed d ata d isp lays one p ixel valu e
after an other an d the m inim u m , m axim u m , and m ean valu e of the sam p led line. Use this
com m and to en su re the p rop er vid eo inp u t range.
Probe the ou tp u t lines w ith an oscilloscop e. Disconnect the d igital cable from the cam era
and check the d igital sign als at the ou tp u t of the cam era. Ensu re that the correct valu es
Содержание DALSA Piranha 2 P2-2x-01K40
