Teledyne ADQ8-4X Скачать руководство пользователя страница 39

Страница: 39 / 46

19-2302 A
2020-09-16

39(46)

ADQ8-4X Manual

19-2302 A 2020-09-16

39(46)

The timing of a user-scheduled multi-record transfer is in

Figure 31

. The acquisition is set up and

armed. The user’s software checks for available records. The available records can be transfered with
the

GetDataWHTS

command

DESCRIPTION

A/D Converter delivers a stream of data int the acquisition engine.

The acquisition engine applies triggers, headers, etc.

Data is sent in real-time to the FIFO on the ADQ.

The DMA transfers data to the PC when requested by the user.

Kernel buffers in the host PC receives the data from the digitizer.

The ADQAPI receives incoming data and do necessary pre-processing, for example lost packages, and
sends data to the user’s buffers.

User’s buffers in RAM. These are accessed via API commands.

The user’s application sets up the digitizer for acquiring data. Then the software requests the acquired data
and perform application specific processing. This is the user’s software.

Examples of output devices.

Figure 30: Block diagram of user-scheduled data transfer.

1. WHTS means ‘with header and timestamp’.

)

*+,

2#'3

%##

2###

*+##

452

.#/

.,/

Содержание ADQ8-4X















































Результаты поиска

Содержание ADQ8-4X

Отзывы:

Teledyne ADQ8-4X, Руководство пользователя, Страница: 39 / 46

Результаты поиска

Содержание ADQ8-4X

Отзывы: