Teledyne ADQ8-4X Скачать руководство пользователя страница 12

Страница: 12 / 46

19-2302 A
2020-09-16

12(46)

ADQ8-4X Manual

19-2302 A 2020-09-16

12(46)

TRIGGER

4.1 Trigger block diagram

DESCRIPTION

USER COMMAND

REF

Each analog input is connected to a level trigger block.

SetupLevelTrigger

4.10

Select on which channel to trigger (when using level trigger).

SetupLevelTrigger

4.10

Internal trigger generator.

SetInternalTriggerPeriod

4.11

A software trigger is available for user control.

SWTrig

4.7

External trigger input from backplane (different in PXIe and MTCA)

4.9

External trigger input on front panel connector TRIG.

4.8.1

External trigger input on front panel connector SYNC.

4.8.2

Select which type of trigger to activate.

SetTriggerMode

The trigger blocking function controls the flow of triggers to the
acquisition engine.

SetupTriggerBlocking

4.5

Select which channels to record data from.

MultirecordSetChannelMask

Acquisition engine creates a record from streaming data

Records are sent to data FIFO for transfer to the host PC

m Activate trigger output and select source.

SetupTriggerOutput

4.12

Select trigger output connector

SetupTriggerOutput

4.12

Frame sync is a function that can group triggers.

SetupFrameSync

4.12.2

Select source for sync output

SetupTriggerOutput

Daisy chain trigger for synchronization

4.13

Figure 4: Trigger source selection and setup

'()

+,-

+ -

+0-

% &

1(12

(

'()

+-
+ -

1 ,

% &

+.-

Содержание ADQ8-4X















































Результаты поиска

Содержание ADQ8-4X

Отзывы:

Teledyne ADQ8-4X, Руководство пользователя, Страница: 12 / 46

Результаты поиска

Содержание ADQ8-4X

Отзывы: