Teledyne ADQ8-4X Скачать руководство пользователя страница 2

Страница: 2 / 46

19-2302 A
2020-09-16

2(46)

ADQ8-4X Manual

19-2302 A 2020-09-16

2(46)

Table of content

INTRODUCTION ........................................................................................................... 5

1.1

ADQ8-4X Architecture ................................................................................................... 5

1.2

Fundamental design properties ..................................................................................... 5

1.3

Digitizer Studio overview................................................................................................ 8

SETTING UP THE ANALOG FRONT-END ................................................................... 9

2.1

ADQ8-4X AFE block diagram ........................................................................................ 9

2.2

Set analog input range................................................................................................... 9

2.3

Set analog DC-offset.................................................................................................... 10

2.4

Adjusting the digital gain and offset ............................................................................. 10

SIGNAL QUALITY ENHANCEMENT........................................................................... 11

3.1

Digital Baseline Stabilizer ............................................................................................ 11

TRIGGER..................................................................................................................... 12

4.1

Trigger block diagram .................................................................................................. 12

4.2

Introduction .................................................................................................................. 13

4.3

Position of the trigger in the data ................................................................................. 13

4.4

Timestamp ................................................................................................................... 14

4.4.1 Timestamp definitions................................................................................................................ 14
4.4.2 Timestamp reset ........................................................................................................................ 14

4.5

Blocking triggers for synchronization ........................................................................... 16

4.6

Trigger jitter.................................................................................................................. 19

4.7

Software trigger............................................................................................................ 20

4.8

External Trigger Inputs................................................................................................. 21

4.8.1 External trigger TRIG front panel connector ..............................................................................  21
4.8.2 External trigger SYNC connector...............................................................................................  22
4.8.3 Driving the external TRIG/SYNC signal by controlling input impedance ...................................  22

4.9

External trigger in the backplane ................................................................................. 23

4.9.1 PXIe interface ............................................................................................................................ 23

4.10 Level trigger ................................................................................................................. 24

4.10.1Setting the level trigger level......................................................................................................  25
4.10.2Level trigger and DBS................................................................................................................  25
4.10.3Controlling noise sensitivity .......................................................................................................  25

4.11 Internal trigger.............................................................................................................. 26
4.12 Trigger output............................................................................................................... 26

4.12.1Trigger output port selection ...................................................................................................... 26

Содержание ADQ8-4X















































Результаты поиска

Содержание ADQ8-4X

Отзывы:

Teledyne ADQ8-4X, Руководство пользователя, Страница: 2 / 46

Результаты поиска

Содержание ADQ8-4X

Отзывы: