Teledyne Photometrics KINETIX Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 48

Teledyne Photometrics KINETIX Скачать руководство пользователя страница 17

8

58-723-004 Rev A01

The default DIP Switch pin settings for the PCIe card are shown below. This will allow the
user to run one or two cameras off the PCIe card at the full speeds available.

Connecting
Kinetix to PCI
Express Bus

The two Kinetix camera data cables are identical, quick-insertion, quick-release cables that
connect the interface card and the camera. One of these cables is shown below.

Note: The PCIe data cables’ connectors can only be inserted into the PCIe ports when
correctly oriented; do not force the connectors. If a connector does not insert, simply turn
the connector over and retry.

To ensure proper system performance, one of the cables should be used to connect the
camera’s PCIe port 1 to the PCIe interface card’s port 1. (Either end of the cable can be
plugged into either device.) The other cable should be used to connect the camera’s PCIe
port 2 to the PCIe interface card’s port 2. (Again, either end of the cable can be plugged
into either device.) See the following two figures

. Here, both ends of one cable have been

wrapped with white tape to differentiate it from the other cable.

PCIe cables inserted into camera’s PCIe ports.

«
...
15
16
17
18
19
...
»

Содержание KINETIX

















































Отзывы:

Нет отзывов