Telect DSX-3 Скачать руководство пользователя страница 25

Страница: 25 / 26

Telect, Inc. • USA +1.509.926.6000 • 52.33.3836.37.52
www.telect.com • © 2010 Telect, Inc., All Rights Reserved, 139256 A0

Page 4-21

Chapter 4: Service

4.1 Owner Maintenance

Telect’s BCS 4R components do not need preventive maintenance. The only service you can
perform is to replace these assemblies if they fail:

•

DSX Card Module

•

Repeater Card Module

•

DNI Card Module

•

Chassis

•

Tracer lamp LEDs, on card and on backplane

4.2 Troubleshooting Cross-Connected Signals

Check for correct and firm cable connections at the termination and cross-connect points on
every card.

4.3 Replacing the Tracer Lamp LED

Pull the LED assembly and plastic holder straight out.

If LED polarization is not correct, the replacement will not work. Orient the new LED in the plastic
holder the same as the original. The shape of the LED holder slot in the DSX module is keyed for
proper LED insertion.

4.4 Service

4.4.1 In-Warranty Service

Contact your Telect equipment distributor, or call a Telect Customer Service Representative:

1-800-551-4567
1-509-926-6000

Telect will repair or replace defective products within the limits of the warranty. See “Repacking
for Shipment” in this section.

Call a Customer Service Representative for a Return Material Authorization (RMA) before
returning any equipment.

Содержание DSX-3

























Результаты поиска

Содержание DSX-3

Отзывы:

Бренды по названию

Популярные бренды

Telect DSX-3, Руководство пользователя

Результаты поиска

Содержание DSX-3

Отзывы:

Бренды по названию

Популярные бренды