manualshive.com logo in svg

Telect DSX-3, Руководство пользователя

Поделиться
Скачать
Telect DSX-3 Скачать руководство пользователя страница 15

Telect, Inc. • USA +1.509.926.6000 • 52.33.3836.37.52
www.telect.com • © 2010 Telect, Inc., All Rights Reserved, 139256 A0

Page 2-11

2.3 Installation

1. Mount the BCS 4R chassis, along with designation cards, to a rack, using the four supplied 

mounting screws (two per side). Torque to 35 in.-lbs (4.29 N•m.).

 

Figure 7 - Mounting Chassis to Rack

2. Install cable management rings on the rear rack flange using the hardware provided.

3. Repeat Steps 1 and 2 to install all BCS 4R chassis before installing power and I/O cables to 

any BCS 4R chassis in the rack.

4. For BCS 4R chassis that require power, route power from the power distribution panel to con-

nectors on the rear of BCS 4R chassis. 

Use wire in the 10-22 AWG range. Strip away about 

3

/8

 in. (~10 mm) of insulation and then 

press in on the tab at the top of the connector to open the connector’s jaws. Insert the wire 
below the tab and then release the tab to cinch the wire.

Содержание DSX-3



























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды