Telect 125DM08 Скачать руководство пользователя страница 6

Страница: 6 / 18

1.509.926.6000 :: telect.com

Demarcation Fuse/Circuit Breaker Alarm Panel

Power :: Model 125DM08

1.4.2 Installation Procedure

NOTE: Panel brackets are available for flush mounting in a 19-in. rack. A pair of 23-in. rack brackets are also

included. Either pair of brackets can be moved or installed to extend front of panel beyond the face of the rack in

1-in. (2.54 cm) increments.

WARNING

WARNING! Failure to properly ground this equipment can create hazardous conditions to installation

personnel and to the equipment.

NOTE: Input and output wire size for this panel must be rated for the corresponding breaker/fuse size at the

power distribution unit (PDU). The input wiring to this panel may be a greater size to accommodate a voltage drop

from the primary power source.

WARNING! Before connecting input power cables, make sure input power to panel is turned off.

NOTE: Always follow operating company guidelines when connecting input wiring to the primary power source.

CAUTION

CAUTION!

Make sure the alarm connector on the fuse holder is straight before

inserting into the panel.

A bent alarm bayonet on a fuse holder can either cause internal damage to the

panel or fail to make electrical contact with the alarm wiring within the panel.

LINE & LO AD designations are on

bottom of TPC fuse holders on

THIS side of the panel.

Bezel

LINE & LO AD designations are on

top of TFD fuse holders on THIS

side of the panel.

Bezels

LINE

LOAD

LINE

LOAD

TFD Fuse Holder

TPC Fuse Holder

M AKE SURE ALARM

CO NNECTO R O N FUSE HO LDER

IS STRAIT BEFO RE INSERTING

INTO THE PANEL

A bent alarm bayonet on a fuse

holder can either cause internal

dam age to the panel or fail to m ake

electrical contact with alarm wiring

within the panel.

CAUTION !

Содержание 125DM08

















Результаты поиска

Содержание 125DM08

Отзывы:

Telect 125DM08, Руководство по установке, Страница: 6 / 18

Результаты поиска

Содержание 125DM08

Отзывы: