Date
Code Number:
Series
Model number
Draft
TELECO AUTOMATION SRL -
Viale del Lavoro, 5 - 31014 Colle Umberto (TV) ITALY
TELEPHONE:
++39.0438.388511 FAX: ++39.0438.388536
This document is the property of Teleco Automation Srl who reserves all reproduction and copying rights
T303.01
26-05-08
TVPRH
RADIO CONTROL TVPRH
ATTENTION !
The appliance must be installed only by qualified technical personnel in
compliance with the standards in force. All connections must be rated
for a 230V single-phase power supply. To disconnect the appliance from
the mains use an all-pole switch with a minimum distance of 3.5 mm
between the contacts. All wiring used must guarantee sufficient
insulation as required by electrical safety standards in force.
The programmer only carries out remote and manual movement
commands. All the necessary safety devices required by the installation
are to be organised separately. The programmer is in conformity with
the RAEE and RoHS directives and it is intended for indoor use only
(IPX0). The appliance is not to be used by children.
Children should be watched to make sure they do not play with the
appliance.
The radio frequency reception of the appliance may be disturbed by
several factors as follows:
-radio electric interferences from other appliances in the same room
that are transmitting on the same frequency
-if the appliance is housed in a metal casing; only plastic casing should
be used.
1- GENERAL DESCRIPTION
Electronics for the remote control of tubular motors for rolling shutters
with mechanical or electronic travel limits incorporated in the motor.
Possibility to control the device manually or via radio (in the 868
version). The work time is fixed at 60 seconds.
Programming is either carried out on the receiver or remotely via
transmitters.
This appliance may be commanded by the standard transmitters of the
series TVLink. The standard transmitters may be memorized or
cancelled in the receiver using the command buttons.
The maximum number of codes that can be memorized is 42 .
1.1 Operating mode
It is possible to select different functioning modes. The operating mode
involves both the commands by means of push-buttons and the commands
via radio. These phases are possible only for the first 10 seconds after
having given power to the device.
1.1.1 Automatic opening and closing movement
1) Give power to the device, the Led1 will light up for two seconds.
2) After the two seconds, press at the same time the push-buttons P2+P4
for 8 times and hold them pressed for two seconds. The Led will light up
every time the push-buttons will be pressed.
1.1.2 Automatic opening movement and “present man” closing
movement
1) Give power to the device, the Led1 will light up for two seconds.
2) After the two seconds, press at the same time the push-buttons P2+P4
for 9 times and hold them pressed for two seconds. The Led will light up
every time the push-buttons will be pressed.
1.1.3 “Present man” opening and closing movement
1) Give power to the device, the Led1 will light up for two seconds.
2) After the two seconds, pressh at the same time the push-buttons P2+P4
for 10 times and hold them pressed for two seconds. The Led will light up
every time the push-buttons will be pressed.
2- Transmitters
Use transmitters with at least 2 channels.
The transmitters are pre-coded by the manufacturer and each
transmitter has its own unique code.
Attention: if you press and hold down a transmitter button for more
than 30 seconds, the transmitter with switch off automatically.
The receiver is compatible with all transmitters of the TVlink system:
TVTXV, TVTXP, TVTXC, TVTXK, TVTXQ, TVTXL.
3
TVLink RS868
3- Memorizing transmitters (we suggest that you cancel the
entire memory content before a new installation)
When the buttons P2+P4 are used at the same time (programming
functions) the led lights up each time.
The channels are memorized in pairs, ch1 with ch2, ch3 with ch4, ch5
with ch6 and ch7.
3.1- Memorizing directly on the receiver
1) Press buttons P2+P4 simultaneously for 3 times and then hold them
down, the led will light up and remain lit.
2) Transmit one of the two channels of the pair to be memorized. Once
memorized the led will flash intermittently, release the button.
To insert another pair of channels on the receiver repeat points 1 and 2.
3.2- To cancel a code on the receiver:
1) Press buttons P2+P4 simultaneous for 4 times and then hold them
down, the receiver led will flash intermittently slowly.
2) Transmit one of the two channels of the pair to be cancelled, once
cancelled, the led will light up and remain lit.
To cancel more transmitters repeats points 1-2
3.3- To cancel all codes from memory:
Simultaneously press buttons P2+P4 for 5 times and hold them down for
at least ten seconds, the receiver led will flash rapidly. Once the memory
has been cancelled the led will light up and remain lit.
4 - Memorizing via a transmitter (first installation, empty
memory)
1) Press button P3 on the transmitter, the receiver led will light up and
remain lit.
2) Transmit one of the two channels of the pair to be memorized. Once
memorized the led will flash intermittently, release the button.
To insert another pair of channels via radio follow the procedure in
paragraph 4.1
4.1 - Memorizing via a transmitter (ulterior transmitters)
(memory addressing procedure)
1) Press button P3 on the already memorized transmitter, the receiver
led will light up and remain lit.
2) Within 5 seconds press a channel that is already memorized in the
receiver, the led will switch off for 1 second and then light up again for
5 seconds.
3) Transmit one of the two channels of the pair to be memorized. Once
memorized the led will flash intermittently, release the button.
To memorize more transmitters repeats points 1-2-3.
4.2- To cancel a code via radio
1) Press button P3 on the transmitter for three times within five
seconds, the receiver led will flash slowly.
2) Transmit one of the two channels of the pair to be cancelled, once
cancelled, the led will switch off.
5- If memory is full
If the memory is full the led will flash three times when you are
attempting to memorize.
5.1- Errors during memorizing or cancelling
If the code is not memorized it could be due to one of the following:
- the code already exists in memory;
- the memory is full;
- the addressing procedure has not been followed correctly.
