TeleChips TCC720 Скачать руководство пользователя страница 74

Страница: 74 / 143

TCC720

USB CONTROLLER

32-bit RISC Microprocessor for Digital Media Player
Dec. 16. 2002

Preliminary Spec 0.51

8 - 6

The EP0 interrupt is generated under the following conditions:

1. OUT Packet is ready. ORDY field is set in the CSR register

2. IN Packet is ready. IRDY field is set in the CSR register

3. SENT STALL is set

4. SETUP END is set

5. DATA END is cleared (End of control transfer)

The EP1/E2 interrupt is generated under the following conditions:

For IN endpoints

1. IRDY field is cleared in the CSR register

2. FIFO is flushed

3. SENT STALL is set

For OUT endpoints

1. ORDY field is set in the CSR register.

2. SENT STALL is set

The suspend interrupt is generated when the USB receives suspend signaling. The SP bit field of the

UBIR is set whenever there is no activity for 3ms on the bus. This interrupt is disabled in default. The

resume interrupt is generated by a USB reset in suspend mode. The USB reset interrupt is generated

when USB controller receives the reset signaling from the host.

Содержание TCC720
















































































































































Результаты поиска

Содержание TCC720

Отзывы:

Похожие инструкции для TCC720

Бренды по названию

Популярные бренды

TeleChips TCC720, Руководство пользователя

Результаты поиска

Содержание TCC720

Отзывы:

Похожие инструкции для TCC720

Бренды по названию

Популярные бренды