Tektronix WFM4000 Series Скачать руководство пользователя

Страница: 68 / 79

Using Alarms

For each alarm listed in the table, press
the

SEL

button to enable (when enabled,

there is an

in the box) or disable

(when disabled, the box is blank) it. (See
page 53,

Possible Alarm Responses

Navigate to highlight the

Return

box,

and press the

SEL

button to return to the

Con

guration menu.

Repeat steps 4 through 7 to con

gure as

many types of alarms as you want.

To Set Alarm Responses Globally

Press the

CONFIG

button to display the

Con

guration menu.

Use the arrow keys and

SEL

button to

make selections in the steps that follow.

Select

Alarms

Navigate to

Set all alarms to this mask

Press

SEL

to display a table for setting

the allowed alarm responses that will be
applied to all the alarm categories.

For each alarm listed in the table, press
the

SEL

button to enable (when enabled,

there is an

in the box) or disable

(when disabled, the box is blank) it. (See
page 53,

Possible Alarm Responses

Navigate to highlight the

Return

box,

and press the

SEL

button to return to the

Con

guration menu.

This sets alarms for all alarm categories
to the setting on the global mask.

WFM4000 and WFM5000 Waveform Monitors User Manual

Содержание WFM4000 Series
















































































Результаты поиска

Содержание WFM4000 Series

Отзывы:

Похожие инструкции для WFM4000 Series

Бренды по названию

Популярные бренды

Tektronix WFM4000 Series, Руководство пользователя

Результаты поиска

Содержание WFM4000 Series

Отзывы:

Похожие инструкции для WFM4000 Series

Бренды по названию

Популярные бренды