tekton 46875 Скачать руководство пользователя страница 1

Страница: 1 / 12

WARNING: BEFORE USE, READ AND UNDERSTAND OPERATOR'S MANUAL. Wear impact-resistant protective

eyewear in work area at all times. This reel must only be mounted to a load bearing structural object such as a

stud, rafter, or floor which can support the combined weight of reel and hose and can withstand pulling forces on

hose when in use. Air hose is designed for use on regulated air compressor systems delivering less than 250 PSI.

DO NOT EXCEED 250 PSI. Be sure to restrain hose as it rewinds—do not allow hose to rewind at full speed.

Never exceed air pressure rating for any air tool. Read and follow all guidelines specified in the air tool owner’s

manual. Certain air tools, such as paint spray guns, sanders, grinders, and sandblasting equipment, present

specific dangers and hazards. Consult applicable material safety data sheet for precautions and possible respirator

recommendation.

OPERATOR’S MANUAL

STORE THIS MANUAL IN A SAFE

PLACE FOR FUTURE REFERENCE

AUTO REWIND AIR HOSE REEL

Items

46875, 46878

Save time, contact us first.

888-648-3371

[email protected]

NEED HELP?

Содержание 46875












