background image

Safe Operation on Rough Terrain 

1. Drive  the  mower  slowly  on  hillsides  and  curves  to  eliminate  the  danger  of  tipping.  Avoid
slopes which are too steep for safe operation. Avoid sharp uphill turns.
2. Always drive slowly enough over rough ground or obstructions. Drive at speeds slows enough
to ensure your safety.
3. When  driving  out  of  a  ditch,  gully,  or  up  a  steep  hillside,  engage  the  clutch  slowly.  Avoid
sharp uphill turns.
4. When  descending  steep  grades,  select  a  sufficiently  low  gear  to  maintain  control  with
minimum use of braking.
5. Use caution when driving near the edge of a ditch or gully. It may cave in, causing the mower 
to roll over.
6. Be alert when operating near trees, slopes and around obstructions. Tree branches can cause 
damage to ROPS components.

Maintenance Safety 

1. Remove mud, crop residue, chains, and tools from steps and operator’s platform. They may
interfere with pedal operation or entry/exit from mower.
2. When servicing components are too high to reach from the ground use steps and handholds.
Do not use fenders or shields that are not designed as steps.

Safe Highway Operation 

1. Before operating the mower on, or near, public roadways check with your local authorities
for any local regulations that will affect you.
2. Equip  towed  implements  with  slow  moving  vehicle  (SMV)  signs  when  traveling  on  public
roads.
3. Install additional lights on implement rear to safeguard against rear end collisions.
4. Use hazard warning flashers as required by law when transporting or driving on public roads. 
If the mower had warning flashers removed when mounting the ROPS, they must be replaced
prior to operation on public roads.
5. Keep to the right, yielding right-of-way traffic, especially if pulling implements. Pull off the
road and stop to allow motorists to pass. Drive on the road shoulder, if permitted by law.
6. Use extreme caution when pulling heavy loads at road speeds. Avoid hard application of the
mower brakes at high speed.
7. Always drive slowly near curbs, approaches or ditches.
8. If equipped, ensure headlights are aligned so they will not blind the operator’s of oncoming
vehicles.  If  the  mower  is  not  equipped  with  turn  signals  and  law  requires  them,  install  them
prior to operating on or near public roads.

    June 2021© Toro Reelmaster 5010 Series ROPS Operation Manual 

Содержание Toro Reelmaster 5010 Series




















Отзывы:

Похожие инструкции для Toro Reelmaster 5010 Series