9
NOZZLE CHANGE OPERATION
1. Please use driver with special head for removed
and install nozzle as. (figure 3)
2. Please remove nozzle (figure 4) from burner
with special nozzle driver and install new nozzle.
(figure 5)
VENTILATION OF ROOM
The air needed for burning is received from room
air and the gases emitted are given directly in
room. For safe operation of your product, good
room ventilation is a precondition. If no window or
room to be utilized for room ventilation is available,
additional ventilation should be installed.
Room size / Ventilating opening
Smaller than 5 m³ / min. 100 cm²
Between 5 m³ - 10 m³ / min. 50 cm²
Bigger than 10 m³ / not required
In basement or cellar / min. 65 cm²
REDUCED GAS FLOW RATE SETTING FOR HOB TAPS
1. Ignite the burner that is to be adjustment and
turn the knob to the reduced position.
2. Remove the knob from the gas tap.
3. Use an appropriately sized screwdriver to
adjust the flow rate adjustment screw. For LPG
(butane-pro pane) turn the screw clockwise.
For the natural gas, you should turn the screw
counter- clockwise once.
“The normal length of a straight flame in the
reduced position should be 6-7 mm.“
4. If the flame is higher then the desired position,
turn the screw clockwise. If it is smaller turn
anticlockwise.
5. For the last control, bring the burner both to
high-flame and reduced positions and check
whether the flame is on or off.
Depending on the type of gas tap used in your
appliance the adjustment
screw position may vary.
To adjust your oven acc. to the gas type, make
the adjustment for reduced flame carefully by
turning with a small screwdriver as shown below
on the screw in the middle of the gas cocks as
well as nozzle changes (figure 6 and 7).
GAS CONNECTION (CONT.)
19
Nozzle change operation
1.
Please use driver with special head for removed and install nozzle as.
(figure 3)
2.
Please remove nozzle (figure 4) from burner with special nozzle driver
and install new nozzle. (figure 5)
Ventilation of room
The air needed for burning is received from room air and the gases emitted
are given directly in room. For safe operation of your product, good room
ventilation is a precondition. If no window or room to be utilized for room
ventilation is available, additional ventilation should be installed. However,
room has a door opening outside, it is no needed to vent holes.
Room size
Ventilating opening
Smaller than 5 m³
min. 100 cm²
Between 5 m³ - 10 m³
min. 50 cm²
Bigger than 10 m³
no need
In basement or cellar
min. 65 cm²
Figure 3
Figure 4
Figure 5
20
Reduced gas flow rate setting for hob taps
1.
Ignite the burner that is to be adjustment and turn the knob to the
reduced position.
2.
Remove the knob from the gas tap.
3.
Use an appropriately sized screwdriver to adjust the flow rate adjustment
screw. For LPG (butane-pro pane) turn the screw clockwise. For the
naturel gas, you should turn the screw counter- clockwise once.
“The normal length of a straight flame in the reduced position should
be 6-7 mm.“
4.
If the flame is higher then the desired position, turn the screw clockwise.
If it is smaller turn anticolockwise.
5.
For the last control, bring the burner both to higt-flame and reduced
positions and check whether the flame is on or off.
Depending on the type of gas tap used in your appliance the adjustment
screw position may vary.
To adjust your oven acc. to the gas type, make the adjustment for
reduced flame carefully by turning with a small screwdriver as shown
below on the screw in the middle of the gas cocks as well as nozzle
changes (figure 6 and 7).
Figure 6
Figure 7
19
Nozzle change operation
1.
Please use driver with special head for removed and install nozzle as.
(figure 3)
2.
Please remove nozzle (figure 4) from burner with special nozzle driver
and install new nozzle. (figure 5)
Ventilation of room
The air needed for burning is received from room air and the gases emitted
are given directly in room. For safe operation of your product, good room
ventilation is a precondition. If no window or room to be utilized for room
ventilation is available, additional ventilation should be installed. However,
room has a door opening outside, it is no needed to vent holes.
Room size
Ventilating opening
Smaller than 5 m³
min. 100 cm²
Between 5 m³ - 10 m³
min. 50 cm²
Bigger than 10 m³
no need
In basement or cellar
min. 65 cm²
Figure 3
Figure 4
Figure 5
19
Nozzle change operation
1.
Please use driver with special head for removed and install nozzle as.
(figure 3)
2.
Please remove nozzle (figure 4) from burner with special nozzle driver
and install new nozzle. (figure 5)
Ventilation of room
The air needed for burning is received from room air and the gases emitted
are given directly in room. For safe operation of your product, good room
ventilation is a precondition. If no window or room to be utilized for room
ventilation is available, additional ventilation should be installed. However,
room has a door opening outside, it is no needed to vent holes.
Room size
Ventilating opening
Smaller than 5 m³
min. 100 cm²
Between 5 m³ - 10 m³
min. 50 cm²
Bigger than 10 m³
no need
In basement or cellar
min. 65 cm²
Figure 3
Figure 4
Figure 5
