8
GAS CONNECTION
WARNING
: Before starting any work related
with gas installation, turn off gas supply. Risk
of explosion. Please operate your oven in dry
atmosphere.
1. Fit the clamp to the hose. Push one of the hose
until it goes to the end of the pipe.
2. For the sealing control; ensure that the buttons
in the control panel are closed, but the gas
cylinder is open. Apply some soap bubbles to
the connection. If there is gas leakage, there will
be foaming in the soaped area.
3. The oven should be using a well ventilation
place and should be Installed on flat ground.
4. Re-inspect the gas connection.
5. When placing your oven to its location, ensure
that it is at the counter level. Bring it to the
counter level by adjusting the feet if necessary.
6. Do not make gas hose and electrical cable
of your oven go through the heated areas,
especially through the rear side of the oven. Do
not move gas connected oven. Since the forcing
shall loosen the hose, gas leakage may occur.
7. Please use flexible hose for gas connection.
FOR LPG GAS CONNECTION
For LPG (cylinder) connection, affix metal clamp on
the hose coming from LPG cylinder. Affix an edge
of the hose on hose inlet connector behind the
appliance by pushing to end through heating the
hose in boiled water. Afterward, bring the clamp
towards end section of the hose and tighten it with
screwdriver. The gasket and hose inlet connector
required for connection is as the picture shown
below.
NOTE: The regulator to be affixed on LPG cylinder
should have 300mmSS feature.
FOR NATURAL GAS CONNECTION
WARNING
: Natural gas connection should be done
by an authorized service person. For natural gas
connection, place gasket in the nut at the edge of
natural gas connection hose. To install the hose
on main gas pipe, turn the nut. Complete the
connection by making gas leakage control.
GAS HOSE PASSAGEWAY
Connect the appliance to the gas piping tap in
shortest possible route and in a way that ensure no
gas leakage will occur.
In order to carry on a tightness and sealing safety
check ensure that the knobs on the control panel
are closed and the gas cylinder is open.
WARNING:
While performing a gas leakage check,
never use any kind of lighter, match, cigarette or
similar burning substance.
Apply soap bubble on the connection points. If
there is any kind of leakage then it will cause
bubbling. While inserting the appliance in place
ensure that it is on the same level with the worktop.
If required adjust the legs in order the make level
with the worktop. Use the appliance on a level
surface and in a well ventilated environment.
WARNING
: Before placing the appliance, check
that the local distribution conditions (gas type and
pressure) conform to the product settings.
18
For natural gas connection;
Gas hose passage way
Connect the appliance to the gas piping
tap in shortest possible route and in
a way that ensure no gas leakage will
occur.
In order to carry on a tightness and
sealing safety check ensure that the
knobs on the control panel are closed
and the gas cylindir is open.
WARNING:
While performing a gas
leakage check, never use any kind
of lighter, match, cigarette or similar
burning substance.
Apply soap bubble on the connection
points. If there is any kind of leakage
then it will cause bubbling.
While inserting the appliance in place
ensure that it is on the same level with
the worktop. If required adjust the
legs inorder the make level with the
worktop.
Use the appliance on a level surface
and in a well ventilated environment.
WARNING:
Before placint the appliance, check that the local distribution
conditions (gas type and pressure) conform to the product settings.
Main Gas Pipe
Gasket
Nut
Natural Gas
Connection Hose
WARNING:
Natural gas connection should
be done by authorized service.
For natural gas connection, place gasket
in the nut at the edge of natural gas connection
hose. To install the hose on main gas pipe,
turn the nut. Complete the connection by
making gas leakage control.
Figure 1
Figure 2
17
Gas Connection
WARNING:
Before starting any work related with gas installation, turn off
gas supply. Risk of explosion.
Please operate your oven in dry atmosphere.
1.
Fit the clamp to the hose. Push one of the hose until it goes to the
end of the pipe.
2.
For the sealing control; ensure that the buttons in the control panel are
closed, but the gas cylinder is open. Apply some soap bubbles to the
connection. If there is gas leakage, there will be foaming in the soaped area.
3.
The oven should be using a well ventilation place and should be
install on flat ground.
4.
Re-inspect the gas connection.
5.
When placing your oven to its location, ensure that it is at the counter
level. Bring it to the counter level by adjusting the feet if necessary.
6.
Do not make gas hose and electrical cable of your oven go through theheated
areas, especially through the rear side of the oven. Do not move gas connected
oven. Since the forcing shall loosen the hose, gas leakage may occur.
7.
Please use flexible hose for gas connection.
For LPG connection;
1.
For LPG (cylinder) connection, affix
metal clamp on the hose coming from LPG
cylinder. Affix an edge of the hose on hose
inlet connector behind the appliance by
pushing to end through heating the hose
in boiled water. Afterward, bring the clamp
towards end section of the hose and tighten
it with screwdriver. The gasket and hose
inlet connector required for connection is
as the picture shown below.
NOTE:
The regulator to be affixed on LPG cylinder should have 300
mmSS feature.
Main Gas Pipe
Gasket
Hose Inlet Connector
Metal Clamp
Lpg Connection Hose
18
For natural gas connection;
Gas hose passage way
Connect the appliance to the gas piping
tap in shortest possible route and in
a way that ensure no gas leakage will
occur.
In order to carry on a tightness and
sealing safety check ensure that the
knobs on the control panel are closed
and the gas cylindir is open.
WARNING:
While performing a gas
leakage check, never use any kind
of lighter, match, cigarette or similar
burning substance.
Apply soap bubble on the connection
points. If there is any kind of leakage
then it will cause bubbling.
While inserting the appliance in place
ensure that it is on the same level with
the worktop. If required adjust the
legs inorder the make level with the
worktop.
Use the appliance on a level surface
and in a well ventilated environment.
WARNING:
Before placint the appliance, check that the local distribution
conditions (gas type and pressure) conform to the product settings.
Main Gas Pipe
Gasket
Nut
Natural Gas
Connection Hose
WARNING:
Natural gas connection should
be done by authorized service.
For natural gas connection, place gasket
in the nut at the edge of natural gas connection
hose. To install the hose on main gas pipe,
turn the nut. Complete the connection by
making gas leakage control.
Figure 1
Figure 2
18
For natural gas connection;
Gas hose passage way
Connect the appliance to the gas piping
tap in shortest possible route and in
a way that ensure no gas leakage will
occur.
In order to carry on a tightness and
sealing safety check ensure that the
knobs on the control panel are closed
and the gas cylindir is open.
WARNING:
While performing a gas
leakage check, never use any kind
of lighter, match, cigarette or similar
burning substance.
Apply soap bubble on the connection
points. If there is any kind of leakage
then it will cause bubbling.
While inserting the appliance in place
ensure that it is on the same level with
the worktop. If required adjust the
legs inorder the make level with the
worktop.
Use the appliance on a level surface
and in a well ventilated environment.
WARNING:
Before placint the appliance, check that the local distribution
conditions (gas type and pressure) conform to the product settings.
Main Gas Pipe
Gasket
Nut
Natural Gas
Connection Hose
WARNING:
Natural gas connection should
be done by authorized service.
For natural gas connection, place gasket
in the nut at the edge of natural gas connection
hose. To install the hose on main gas pipe,
turn the nut. Complete the connection by
making gas leakage control.
Figure 1
Figure 2
