background image

© 

2010     D 

132 

04/10 

of 

12 

Connecting The Control

 ---------------------------------------------------------

Make sure all power to the devices and terminal blocks is off, and remove any 
remaining jumpers from the terminals. 

Reconnect the terminal blocks to the control by carefully aligning them with their respec-
tive headers on the control and then pushing the terminal blocks into the headers. The 
terminal blocks should snap firmly into place. 

Install the supplied safety dividers between the unpowered sensor input and the pow-
ered 120 V (ac) or 24 V (ac) wiring chambers. 

Apply power to the control. The operation of the control on power up is described in the 

Sequence of Operation

 section of this brochure. 

WARM WEATHER SHUT DOWN (WWSD)  ---------------------------------------------------

 ---------------------------------------------------  

The 

WWSD

 dial is only operational when an outdoor sensor is installed. The WWSD dial

can be set from 35 to 100°F or Off (2 to 38°C or Off). Refer to section A.

Note:

 If an outdoor sensor is not installed, the 

WWSD

 dial must be set to 

Off

FREQUENCY OF ROTATION ---------------------------------------------------------------------

 ---------------------------------------------------------------------  

The 

Frequency of Rotation

 dial can be set from 12 to 168 hours or Off. Refer to section A. 

30 second Delay / 10 second Delay

 

-----------------------------------------------------------------------------------

 

The 

30 second Delay / 10 second Delay

 DIP switch is used to select what time delay is required to prove flow once a pump 

contact is turned on. Refer to section A. 

Exercising / Off

 ---------------------------------------------------------------------------------------------------------

 

The 

Exercising / Off

 DIP switch is used to select exercising. If the DIP switch is set to 

Exercising

, refer to section A. 

Alert per Pump / Alert Levels

 -----------------------------------------------------------------------------------------

 

The 

Alert per Pump / Alert Levels

 DIP switch is used to select which mode of alert operation is required. Refer to section C. 

Settings

13 14

16

15

A     A

Alert

Alert

B     B

WWSD

35

Off

70° F

 

 

100

Frequency of Rotation

12

Off

96 hours

168

48

144

2-Stage

Alert Levels

Pump

1  2

Auto

30 second Delay

Exercising
Alert per Pump

Off

10 second Delay

Off

Stand-by

DIP SWITCH SETTINGS  ----------------------------------------------------------------------------------------------------------------------------

 ----------------------------------------------------------------------------------------------------------------------------

Pump 1 Auto / Off

 -----------------------------------------------------------------

The 

Pump 1 Auto / Off

 DIP switch is used to select pump 1 operation. If the DIP switch 

is set to 

Pump 1 Auto

, refer to section B. 

 

Pump 2 Auto / Off

 ----------------------------------------------------------------

 

The 

Pump 2 Auto / Off

 DIP switch is used to select pump 2 operation. If the DIP switch 

is set to 

Pump 2 Auto

, refer to section B. 

2-Stage / Stand-by

 ---------------------------------------------------------------

The 2-Stage / Stand-by DIP switch is used to select which mode of pump control is 
required. If 2-Stage is selected, refer to section B2, and if Stand-by is selected, refer to 
section B1. 
 

Содержание Pump Sequencer 132













Отзывы: