background image

28

INSTALLATION 

CLEANING 

IMPORTANT:
always  disconnect  the  appliance  from  the  gas
and  electricity  mains  before  carrying  out  any
cleaning operation.

2) HOT PLATE

Periodically wash the gas hob, the enamelled stell
pan  support,  the  enamelled  burner  caps  “A”,  “B”
and “C” and the burner heads "T" (see fig. 6 and
6/A) with lukewarm soapy water. They should also
be  cleaned  plugs  "AC"  and  flame  detection  "TC"
(see fig. 6). Clean them gently with a small nylon
brush as shown (see fig. 6/B) and allow to dry fully.
It is very important to clean the surface soon after
every  use,  when  the  glass  is  still  tepid.  Do  not
wash in the dishwasher. 
Do  not  allow  vinegar,  coffee,  milk,  salted  water,
lemon  or  tomato  juice  from  remaining  in  contact
with  the  enamelled  surfaces  for  long  periods  of
time.  Do  not  use  metallic  sponges,  powder
abrasives or corrosive sprays.

WARNINGS:
comply  with  the  following  instructions,  before
remounting the parts:
- check that burner head slots “T” (fig. 6) have

not become clogged by foreign bodies.

- Check that enamelled burner cap “A - B - C”

(fig. 6 - 6/A) have correctly positioned on the
burner head. It must be steady.

-  The  pan  support  must  be  placed  in  the

appropriate  centering  pins,  (or  on  the
aluminium  profile  if  present).  Verifying  the
perfect stability. 

- Do not force the taps if they are difficult open

or  close.  Contact  the  technical  assistance
service for repairs.

-  Don’t  use  steam  jets  for  the  equipment

cleaning.

TECHNICAL INFORMATION 

FOR THE INSTALLER

Installation,  adjustments  of  controls  and

maintenance  must  only  be  carried  out  by  a

qualified engineer.

The  appliance  must  be  correctly  installed  in

conformity  with  current  law  and  the

manufacturer's instructions.

Incorrect  installation  may  cause  damage  to

persons,  animals  or  property  for  which  the

Manufacturer  shall  not  be  considered

responsible.

During  the  life  of  the  system,  the  automatic

safety  or  regulating  devices  on  the  appliance

may  only  be  modified  by  the  manufacturer  or

by his duly authorized dealer. 

3) INSTALLING THE HOT PLATE

Check that the appliance is in a good condition after
having  removed  the  outer  packaging  and  internal
wrappings  from  around  the  various  loose  parts.  In
case of doubt, do not use the appliance and contact
qualified personnel.

Never leave the packaging materials (cardboard,
bags,  polystyrene  foam,  nails,  etc.)  within
children’s  reach  since  they  could  become
potential sources of danger.

The measurements of the opening made in the top of
the modular cabinet and into which the hot plate will be
installed  are  indicated  in  either  fig.  7. Always  comply
with  the  measurements  given  for  the  hole  into  which
the appliance will be recessed (see fig. 7 and 8).

The  appliance  belongs  to  class  3  and  is

therefore  subject  to  all  the  provisions

established  by  the  provisions  governing  such

appliances.

CAUTION: 

do  not  place  the  glass  directly  on  the  unit.  The

bottom of the hob must rest on the unit.

Содержание GZC 31330 XBB





































































Отзывы: