Tek Drive TDS-F8, Инструкция по эксплуатации

Страница: 60 / 74

58
1-06
Middle Output Frequency (Hz) 0.1~ 400.0 1.5
1-07
Voltage at Middle Output Frequency (V) 0.1~ 255.0 7.9
1-08
Minimum Output Frequency (Hz) 0.1~ 400.0 1.5
1-09
Voltage at Minimum Output Frequency (V) 0.1~ 255.0 7.9
1-10
Frequency Reference Upper Limit 0~ 109
％
100
％
*
1-11
Frequency Reference Lower Limit 0~ 109
％
0
％
*
1-12
Accelerating Time 1 0.0~ 999.9s 10.0s(
☆
)
1-13
Decelerating Time 1 0.0~ 999.9s 10.0s(
☆
)
1-14
Accelerating Time 2 0.0~ 999.9s 10.0s(
☆
)
1-15
Decelerating Time 2 0.0~ 999.9s 10.0s(
☆
)
1-16
JOG Frequency Reference 0.0~ 400.0Hz 6.0Hz(
☆
)
1-17
S-curve Time at the Starting of Acceleration 0.0~ 1.0s 0.0s
1-18
S-curve Time at the Ending of Acceleration 0.0~ 1.0s 0.0s
1-19
S-curve Time at the Starting of Deceleration 0.0~ 1.0s 0.0s
1-20
S-curve Time at the Ending of Deceleration 0.0~ 1.0s 0.0s
*: The setting value of 1-10 must
≧
1-11.
2- Operating Method Parameters (RUN Command and Frequency Reference Source)
No. Parameter Name & Description Setting Range Default User set
2-01
Run Command Source Selection:
0- Operator
2- RS-485 Modbus
1- Control Terminals
0
2-02
Frequency Reference Source Selection:
0- Operator 2- RS-485 Modbus
1- Control Terminal- AIN 3-Reference POT of Operator
0
2-03
Stop Method Selection:
0- Decelerating to Stop
1-Coast to Stop (Free Run)
0
2-04
Function of STOP key at OP Selection:
0- STOP Key is enabled
1- STOP Key is disabled
0
2-05
Reverse Command or/ and Reference prohibits:
0- REV is effectual
1- REV is invalid
0
2-06
Carrier Frequency (= Set Value × 2.5kHz) 1~ 6
4
2-07
FRQ REF Hold Selection of MOP Control by Multi-function DIns
(Parameter 4-08= 24) when F8 stops.
0- FRQ REF Hold during MOP operation is not retained. If a stop
command is given the FRQ REF will reset to 0Hz. The F8 start to run
from FRQ REF Lower Limit (1-11) if Run Command is given next time.
1- FRQ REF Hold during MOP operation is retained. If a stop command is
given the FRQ REF resumes at the Held FRQ REF when Run command
is restored.
1
2-08
Selects whether the key is used when the FRQ REF is set by the OP.
The OP can simulate a MOP by setting this PRMs.
0- The OP MOP mode is disabled. The F8 accepts the FRQ REF when the
Key is depressed.
1- The OP MOP mode is enabled. The F8 accepts the FRQ REF as soon as
changes are made with the & Keys, without the Key being
depressed.
0