10-
or
(pan inversion) mode. Once the mode has been selected, press the
button to setup. Idling 8 seconds automatically exit menu mode. Back to the functions
without any change press
button.
Tilt Inversion
Press the
button up to when the
is shown on the display. Pressing
button and the display will blink. Use
and
button to select the
(normal)
or
(tilt inversion) mode. Once the mode has been selected, press the
button to setup. Idling 8 seconds automatically exit menu mode. Back to the functions
without any change press
button.
Press the
button up to when the
is showing on the display. Pressing
button and the display will blink. Use
and
button to select the
(Led on) or
(Led off) mode. Once the mode has been selected, press the
button to setup. Idling 8 seconds automatically exit menu mode. Back to the functions
without any change press
button.
Press the
button up to when the
is showing on the display. Pressing
button and
will blink on the display, use
and
button to adjust
the value from 125 to 255, press
button to store and
will blink on the
display, use
and
button to adjust the value from 125 to 255, press
button to store and
will blink on the display, use
and
button to adjust
the value, press
button to store. Idling 8 seconds automatically exit menu mode.
Back to the functions without any change press
button.
It is good for you to install the unit on the floor or under ceiling. Press the
button up
to when the
is blinking on the display. Use the
button to change to the
mode
(display inversion), It will automatically store after 8 seconds. Or press the
button again return to the mode
(display normal). To go back to the
functions press the
button.
Display normal mode for the fixture putting on the floor.
11-
Display inversion mode for the fixture fixing under ceiling.
Press the
button up to when the
is blinking on the display. Pressing
button, the unit will focus on tilt 90°, and then the unit will focus on tilt 0°, pan 0°,
pan 90°, pan 180°, pan 270° in every pressing
button. To go back to the functions
press the
button again.
Press the
button up to when the
is blinking on the display. Pressing
button and the unit will run self-test by built-in program. To go back to the functions
press the
button again.
Press the
button up to when the
is blinking on the display. Pressing
button and the ambient temperature of lamp will show on the display. To go back to
the functions press the
button again.
Press the
button up to when the
is blinking on the display. Pressing
button and the display will show the number of working hours of the unit. To go
back to the functions press the
button again.
Press the
button up to when the
is blinking on the display. Pressing
button and the display will blink. Use
and
button to select the
(Lamp on) or
(Lamp off) mode. Once the mode has been selected, press the
button to setup. Idling 8 seconds automatically exit menu mode. Back to the
functions without any change press
button.
Press the
button up to when the
is blinking on the display. Pressing
button and all channels of the unit will return to their standard position. It will cost
about 20 seconds and then automatically exit menu mode.
ENTER
MENU
MENU
ENTER
DOWN
UP
ENTER
MENU
Led Display
MENU
ENTER
DOWN
UP
ENTER
MENU
White Balance
MENU
ENTER
DOWN
UP
ENTER
DOWN
UP
ENTER
DOWN
UP
ENTER
MENU
Display Inve rsion
MENU
ENTER
ENTER
MENU
Focus Adjust
MENU
ENTER
ENTER
MENU
Self-Test
MENU
ENTER
MENU
Ambient te mperature of lamp
MENU
ENTER
MENU
Fix ture Hours
MENU
ENTER
MENU
Lamp ON/OFF
MENU
ENTER
DOWN
UP
ENTER
MENU
Rese t
MENU
ENTER
