background image

   

 

 

Page 4-3

 

10 TEGAM WAY • GENEVA, OHIO 44041 • 440-466-6100 • FAX 440-466-6110 • [email protected] 

 

SERVICE INFORMATION 

Warranty 

 

TEGAM, Inc. warrants this product to be free from defects in 

material and workmanship for a period of one year from the 

date of shipment. During this warranty period, if a product 

proves to be defective, TEGAM Inc., at its option, will either 

repair the defective product without charge for parts and 

labor, or exchange any product that proves to be defective. 

 

TEGAM, Inc. warrants the calibration of this product for a 

period of one year from date of shipment. During this period, 

TEGAM, Inc. will recalibrate any product, which does not 

conform to the published accuracy specifications. 

 

In order to exercise this warranty, TEGAM, Inc., must be 

notified of the defective product before the expiration of the 

warranty period. The customer shall be responsible for 

packaging and shipping the product to the designated TEGAM 

service center with shipping charges prepaid. TEGAM Inc. shall 

pay for the return of the product to the customer if the 

shipment is to a location within the country in which the 

TEGAM service center is located. The customer shall be 

responsible for paying all shipping, duties, taxes, and 

additional costs if the product is transported to any other 

locations. Repaired products are warranted for the remaining 

balance of the original warranty, or 90 days, whichever period 

is longer. 

 

 

 

 

 

 

 

 

 

 

 

 

 

Содержание R1L-E2A






















Отзывы: