TeeJet MATRIX 570G Скачать руководство пользователя страница 45

Страница: 45 / 67

●

Marking A and B Points

1. Drive to the desired location of Point A .
2. While the vehicle is in motion, press MARK A ICON

3. Drive along the arc that the pivot would create (a wheel track is a

good guide) to the desired location of Point B .

4. Press the MARK B ICON

to establish the A-B arc.

NOTE: The MARK B ICON

is not available for selection (grayed

out) until the minimum distance is traveled (164 ft / 50.0 m)
or if driving in a straight line.

Use CANCEL MARK ICON to cancel the Mark A command and
revert to the previous A-B guideline (when established).

NOTE: It is not necessary to drive the entire circumference of the

center pivot in order to initiate guidance.

Figure 3-22: Mark A and B Points

mph

acres

1.20

10.5

Mark A

mph

acres

2.60

10.5

Mark B

The console will begin providing navigation information.

Figure 3-23: Circle Pivot Guidance

Swath

acres

5.36

0.0

Last Pass Guidance

Last Pass Guidance offers true last pass navigation. The console will
automatically detect the nearest applied area and establish parallel
guideline based on that area.

NOTE: If a boundary is established but no application occurred

during the boundary process, guidance will not initiate.

Activate Last Pass Guidance

1. Press the screen to activate the icons and select the GUIDANCE

MODE ICON .

2. Select LAST PASS GUIDANCE .

◄

Status Bar Icon will change to .

Figure 3-24: Guidance Mode Selection

Swath

acres

0.0

Last Pass

1. Drive to a desired location to apply the

rst pass.

2. Travel next to the applied area.
The console will begin providing navigation information.

NOTE: If a boundary is established but no application occurred

during the boundary process, guidance will not initiate.

Figure 3-25: Last Pass Guidance

mph

acres

6.2

Create Field Boundary

Field boundaries establish application area and determine the no
apply zone.

NOTE: A Field Boundary can be created in either Last Pass

Guidance while in Vehicle View or during any guidance while
in Field View.

To create a

eld boundary:

1. Drive to a desired location at the perimeter of the

eld/area.

2. While the vehicle is in motion, press BOUNDARY ICON .
3. Travel the perimeter of the

eld/area.

4. Finish boundary:

►

Travel to within a swath width of the starting point. The

boundary will close automatically (the white guideline will turn
black).

►

Press BOUNDARY FINISH ICON . A straight line will

complete the boundary between your current location and the
starting point.

NOTE: If a swath was applied while creating a boundary, the

boundary line will be to the exterior of the applied swath.

NOTE: The BOUNDARY FINISH ICON is not available for

selection (grayed out) until the minimum distance is traveled
(five-times the swath width).

Содержание MATRIX 570G




































































Результаты поиска

Содержание MATRIX 570G

Отзывы:

Похожие инструкции для MATRIX 570G

Бренды по названию

Популярные бренды

TeeJet MATRIX 570G, Руководство пользователя

Результаты поиска

Содержание MATRIX 570G

Отзывы:

Похожие инструкции для MATRIX 570G

Бренды по названию

Популярные бренды