Tecnologic TLK 94 Скачать руководство пользователя страница 16

Страница: 16 / 17

Up to 2 analogue outputs: 0/4 ..20 mA (Load Max. 300

Ω

) or 0/2

..10 V.

Auxiliary supply output / OUT6: 12 VDC / 20 mA Max.
Electrical life for relay outputs: 100000 operat.

Installation category: II
Measurement category: I

Protection class against electric shock: Class II for Front panel
Insulation:

Reinforced insulation between the low voltage section

(supply and relay outputs) and the front panel; Reinforced

insulation between the low voltage section (supply and relay
outputs) and the extra low voltage section (inputs, analogue

outputs, SSR outputs); analogue and SSR outputs optoisolated
respect to the input. 50 V insulation between RS485 and extra low
voltage section.

7.2 - MECHANICAL DATA

Housing: Self-extinguishing plastic, UL 94 V0
Dimensions: 48 x 96 mm DIN, depth 98 mm

Weight: 260 g approx.
Mounting: Flush in panel in 45 x 92 mm hole

Connections: 2 x 1 mm

screw terminals block

Degree of front panel protection : IP 54 mounted in panel with

gasket
Pollution situation: 2

Operating temperature: 0 ... 50 °C
Operating humidity: 30 ... 95 RH% without condensation

Storage temperature: -10 ... +60 °C

7.3 - MECHANICAL DIMENSIONS, PANEL CUT-OUT AND
MOUNTING [mm]

TUN

SET

Out6

TLK 94

Out1 Out2 Out3

Out5

Out4

97,5

89,5

PANEL CUTOUT

RECOMMENDED

min. 10 mm

min

. 2

0 mm

PANEL + GASKET

MAX. 8 mm

BRACKETS

7.4 - FUNCTIONAL FEATURES

Control: ON/OFF, single and double action PID, PID

for motorized

actuators with time positioning
Measurement range: according to the used probe (see range table)

Display resolution: according to the probe used 1/0,1/0,01/0,001
Overall accuracy: +/- (0,2 % fs + 1 digit); PTC/NTC: +/- (0,5 % fs +

1 digit)
Max. cold junction compensation drift (in tc) : 0,04 °C/°C with

operating temperature 0 ... 50 °C after warm-up of 20 min.
Sampling rate: 130 ms.

Serial Interface : RS485 insulated
Communication protocol: MODBUS RTU (JBUS)

Baud rate: Programmable from 1200 ... 38400 baud
Display: Display: 4 digit, 1 Red (PV) h 10mm and 1 green (SV), h

7,5 mm
Compliance: ECC directive EMC 2004/108/CE (EN 61326), ECC

directive LV 2006/95/CE (EN 61010-1).

7.5 - MEASURING RANGE TABLE

-46.0 ... 785.0 °C

-50.8 ... 999.9 °F

-46 ... 785 °C

-50 ... 1445 °F

IRS range “A”

“HCFG” = tc

“SEnS”= Ir.J - Ir.CA

0.0 ... 999.9 °C

32.0 ... 999.9 °F

0 ... 2320 °C

32 ... 4208 °F

tc C

“HCFG” = tc

“SEnS” = C

-199.9 ... 400.0 °C

-199.9 ... 752.0 °F

-250 ... 400 °C

-418 ... 752 °F

tc T

“HCFG” = tc

“SEnS” = t

-50.0 ... 999.9 °C

-58.0 ... 999.9 °F

-50 ... 1760 °C

-58 ... 3200 °F

tc R

“HCFG” = tc

“SEnS” = r

-199.9 ... 999.9 °C

-199.9 ... 999.9 °F

-250 ... 1300 °C

-418 ... 2372 °F

tc N

“HCFG” = tc

“SEnS” = n

-150.0 ... 900.0 °C

-199.9 ... 999.9 °F

-150 ... 900 °C

-252 ... 1652 °F

tc L

“HCFG” = tc

“SEnS” = L

-150.0 ... 750.0 °C

-199.9 ... 999.9 °F

-150 ... 750 °C

-252 ... 1382 °F

tc E

“HCFG” = tc

“SEnS” = E

72.0 ... 999.9 °C

162.0 ... 999.9 °F

72 ... 1820 °C

162 ... 3308 °F

tc B

“HCFG” = tc

“SEnS” = b

0.0 ... 999.9 °C

32.0 ... 999.9 °F

0 ... 1760 °C

32 ... 3200 °F

tc S

“HCFG” = tc

“SEnS” = S

-100.0 ... 999.9 °C

-148.0 ... 999.9 °F

-100 ... 1370 °C

- 148 ... 2498 °F

tc K

“HCFG” = tc

“SEnS” = CrAl

-160.0 ... 999.9 °C

-199.9 ... 999.9 °F

-160 ... 1000 °C

- 256 ... 1832 °F

tc J

“HCFG” = tc

“SEnS” = J

“dP”= 1, 2, 3

“dP” = 0

INPUT

TECNOLOGIC spa - TLK 94

-OPERATING INSTRUCTIONS - Vr.01 - 01/10 - ISTR-MTLK94ENG1 - PAG. 16

Содержание TLK 94


















Результаты поиска

Содержание TLK 94

Отзывы:

Бренды по названию

Популярные бренды

Tecnologic TLK 94, Руководство по эксплуатации

Результаты поиска

Содержание TLK 94

Отзывы:

Бренды по названию

Популярные бренды