Tecnet TS-2116 Скачать руководство пользователя страница 6

Страница: 6 / 16

Items

Product Inspection

Thanks for choosing the TecNet TS-2000 Series radio. Before use, please check that the
following contents are included:

Radio

Qty: 1

TS-2116 or TS-2416

Antenna

Qty: 1

Li-Ion battery

Qty: 1

Charger

Qty: 1

Lanyard Strap

Qty: 1

Belt Clip with screws

Qty: 1

User Manual

Qty: 1

For any damage or lost contents, please contact your Authorized TecNet Dealer.

Note:

For antenna identification, the frequency is marked on the color circle at the bottom of the antenna.

Please charge the battery as follows:

1.Turn off the radio for optimum charging.

2.Plug the AC connector of the adaptor into an AC (110V) outlet.

3.Insert the battery or radio equipped with battery into the charger.

• Red LED indicates battery is charging. Green LED indicates charging is complete.

• The battery is not charged at the factory.

Getting Started

Charging the Battery

Product Inspection

Getting Started

Содержание TS-2116

















Результаты поиска

Содержание TS-2116

Отзывы:

Бренды по названию

Популярные бренды

Tecnet TS-2116, Руководство пользователя

Результаты поиска

Содержание TS-2116

Отзывы:

Бренды по названию

Популярные бренды