background image

19

20

Trouble Shooting

Problem

No Power

The battery power consumes 

quickly after charge.

Can not communicate with other 

members.

Voices of non-group members 

are heard on the channel.

No sound or very low sound are 

received by partner when 

transmitting.

No reception on the channel.

Solution

The battery power may be insufficient. Please charge current battery 
or change to a fully charged battery.

The battery life is finished; a new battery would be required.

Please check if your frequency and CTCSS/DCS are the same with 
other members in your group.
Possibility of being too far away from other members. Please check 
if you are within communication range.

Please change CTCSS/DCS, and change those of your members also.

Please check if the volume is turned to its highest level.

Be sure to speak directly into the microphone on the radio.

You may be too far away from other members and cannot receive. 
Please check if you are within communication range and try again.

Care and Maintenance

These recommendations can help you use the radio 
effectively and years of continued use.

Keep the radio dry. Rain, moisture or other liquid 
may cause damage to the radio.

Do not throw, hit or vibrate the radio. This may cause 
damage to the inner IC or other elements and void 
the warranty.

Do  not  hold  the radio by  the antenna or  external  
audio accessories.

Please use the original or standard antenna. Unapproved 
antenna or modifications of accessories may cause 
damage to the radio.

Cover the earphone/microphone pad when not using 
the radio for a long time.

Use a mild detergent (not corrosive chemicals) and 
cloth to clean the casing.

All recommendations above also refer to the battery, 
charger and accessories. 

Note:

T

rouble Shooting

T

rouble Shooting

Содержание TS-2116

















Отзывы: