manualshive.com logo in svg

Technotherm TTH 55, Инструкция по установке и техническое руководство, Страница: 20 / 22

Поделиться
Скачать
Technotherm TTH 55 Скачать руководство пользователя страница 20

 

 

20  

 

Edition:12/16

 

 

Manual Storage Heater TTS with electronic control 

GB

 

Functional description of the electronic charging device - EL

 

Instructions: 

 

The electronic charging regulator EL is designed for manual and weather - and residual heat - 

dependent charging of the heat accumulators.

 

The controller can recognize and process the following control signals: 

AC: 37/40 % ED, 68/72 % ED, 80 % ED PS, 80 % ED NS 

DC: 0,91 - 1,43 V 

 

PS =

 

Positive disturbance behaviour. Working range between 0% ED and 80% ED 

NS = Negative disturbance behaviour. Working range between 2% ED and 80% ED 

For direct connection.

 

❍

  

Connection of the core probe (thermocouple) 

Connect the positive cable to the R + terminal and the negative cable to the G- terminal. 

❍

 

Connection of the setpoint potentiometer (potentiometer) 

Connect the designated cable of the setpoint to terminal P1. Connecting the DC control voltage 

[0.91 V - 1.43 V] Connect the positive cable to the D + terminal and the negative cable to the D- 

terminal on the charge controller

 

❍

 

Connection of the DC control voltage [0.91 V - 1.43 V]

 

Connect the positive cable to the D + terminal and the negative cable to the D- terminal on the 

charge controller. 

 

When an increased voltage is connected, e.g. 230V, the controller is irreparably damaged. 
The AC control voltage is connected directly to the terminals A1 / Z1, A2 / Z2 of the heat 

accumulator. 

Manual charging of the heat accumulators is only possible with the factory setting of the DIP switches.

 

Danger: 

For green and white thermocouple, the positive 

conductor is green.

 

 

 

Coding switch

 

❍

 

Selection of the control signal (40% ED, 68% 

ED, 80% ED NS, 80% ED PS, etc.) with the DIP 

switches from No. 6 to No. 8, 

  Row S2

 

 

Before commissioning, make sure that the control 

signal of the charge control and of the support 

controller is identical 

Default: 

AV (230V) 80% 

ED -PS

 

 

Switch number / 
Control signal 

6 

7 

8 

DC (0,91-1,43)  

OFF  OFF  ON 

AC (230 V) NS 80 %  ON 

OFF  OFF 

AC (230 V) PS 80 %  ON 

OFF  ON 

AC (230 V) PS 68 %  ON 

ON 

OFF 

AC (230 V) PS 40 %  ON 

ON 

ON 

Default setting 

Содержание TTH 55























Отзывы:

Нет отзывов