manualshive.com logo in svg

Technotherm TTH 55, Инструкция по установке и техническое руководство, Страница: 13 / 22

Поделиться
Скачать
Technotherm TTH 55 Скачать руководство пользователя страница 13

 

 

Edition:10/14 

13 

Manual Storage Heater TTS with electronic control 

GB

 

System Start-up 

 

Note:  The heaters are fed from three circuits: (1) the element feed, (2) the charge 

control and (3) the discharge control circuit. All breakers must be off for the 
heater to be safely de-energized to permit safe servicing. 

Steps to activate the system 

1. 

Control Panel

 - Energize control panel at the circuit breaker. 

2. 

Fans and Thermostats

 - Check proper operation of fans and thermostats. Check to see 

that the fans go ON and OFF with operation of the thermostat. 

3. 

Circuit Breakers

 - Switch "ON" all element feed circuit breakers. 

4. 

Time Synchronization

 - Check the synchronization of the control panel or time clock to 

have it coincide with the time of day meter (see specific control panel instructions for 
further information). 

5. 

First Charge

 - The heater insulation is free from organic binding material. It can thus be 

operated immediately without having to go on full charge in order to purge any odours. It 
is, however, advisable, to ventilate the room well during the initial charging phase.

 

6. 

Current Draw

 - It is wise to check the current draw of each heater. See the Technical 

Data Sheet for the proper amperage. This can be done at the breaker panel or at the 
individual heaters. 

 

 

Room Thermostat 

The room thermostat must be installed according to national and local codes of practice. It 
must also be earthed. 

It is very important that the room thermostat be correctly positioned on the wall. 

•

  Air must be able to circulate freely around the thermostat. 

•

  The thermostat must be protected from direct sunshine and/or draughts. 

•

  Fix the thermostat to an inside wall opposite the heater itself (the ideal position is next to 

the door). 

Содержание TTH 55























Отзывы:

Нет отзывов