Technosoft iPOS4803-SY3 Скачать руководство пользователя страница 5

Страница: 5 / 37



Technosoft 2021

iPOS4803-SY Multi Axis System, EtherCAT Technical Reference

Related Documentation

iPOS4803-SY3 Multi Axis System, EtherCAT   Datasheet (P020.200.E403.DSH)
iPOS4803-SY4 Multi Axis System, EtherCAT   Datasheet (P020.200.E404.DSH)
iPOS4803-SY4 Multi Axis System, EtherCAT   Datasheet (P020.200.P404.DSH)

–

describes the hardware connections of the iPOS4803-SY family of intelligent servo drives including

the technical data and connectors.

EasyMotion Studio –

Quick Setup and Programming Guide (P091.034.ESM-

Quick.Setup.and.Programming.Guide.UM.xxxx)

–

describes the compatible software installation,

drive software setup commissioning, introduction to TML motion programming and motion evaluation

tools.

Help of the EasySetUp software

–

describes how to use

EasySetUp

to quickly setup any Technosoft drive

for your application using only 2 dialogues. The output of EasySetUp is a set of setup data that can be

downloaded into the drive EEPROM or saved on a PC file. At power-on, the drive is initialized with the

setup data read from its EEPROM. With EasySetUp it is also possible to retrieve the complete setup

information from a drive previously programmed.

EasySetUp can be downloaded free of charge

from Technosoft web page

Motion Programming using EasyMotion Studio (part no. P091.034.ESM.UM.xxxx)

–

describes how to

use the EasyMotion Studio to create motion programs using in Technosoft Motion Language (TML).

EasyMotion Studio platform includes

EasySetUp

for the drive/motor setup, and a

Motion Wizard

for

the motion programming. The Motion Wizard provides a simple, graphical way of creating motion

programs and automatically generates all the TML instructions.

With EasyMotion Studio you can fully

benefit from a key advantage of Technosoft drives – their capability to execute complex motions

without requiring an external motion controller, thanks to their built-in motion controller.

A demo

version of EasyMotion Studio (with EasySetUp part fully functional) can be downloaded free of

charge from the Technosoft web page

CoE Programming

(part no. P091.064.UM.xxxx)

–

describes how to program the Technosoft

intelligent drives equipped with EtherCAT® communication interface. These drives support CAN

application protocol over EtherCAT® (CoE) in conformance with CiA 402 device profile. The manual

presents the object dictionary associated with this profile. The manual also explains how to combine

the Technosoft Motion Language and the CoE commands in order to distribute the application between

the EtherCAT® master and the Technosoft drives.

Motion Programming using EasyMotion Studio (part no. P091.034.ESM.UM.xxxx)

–

describes how to

use the EasyMotion Studio to create motion programs using in Technosoft Motion Language (TML).

EasyMotion Studio platform includes

EasySetUp

for the drive/motor setup, and a

Motion Wizard

for

the motion programming. The Motion Wizard provides a simple, graphical way of creating motion

programs and automatically generates all the TML instructions.

With EasyMotion Studio you can fully

benefit from a key advantage of Technosoft drives – their capability to execute complex motions

without requiring an external motion controller, thanks to their built-in motion controller.

A demo

version of EasyMotion Studio (with EasySetUp part fully functional) can be downloaded free of

charge from the Technosoft web page

Содержание iPOS4803-SY3






































Результаты поиска

Содержание iPOS4803-SY3

Отзывы:

Похожие инструкции для iPOS4803-SY3

Бренды по названию

Популярные бренды

Technosoft iPOS4803-SY3, Техническое описание

Результаты поиска

Содержание iPOS4803-SY3

Отзывы:

Похожие инструкции для iPOS4803-SY3

Бренды по названию

Популярные бренды