background image

RECLINE EXCITE: Service & Maintenance Manual - rev. 1.1 

 

Page 1.1 

1.  GENERAL NOTICES 

1.1.   INTRODUCTION 

This document is reserved for Technogym Service technicians, and is intended to provide 
authorized personnel with the necessary information to correctly carry out repairs and maintenance. 
A thorough knowledge of the technical information contained in this manual is essential for 
completing the professional training of the operator. 
 
In order to facilitate consultation, the paragraphs are accompanied by schematic drawings which 
illustrate the procedure being described. 
 
This manual contains notices and symbols which have a specific meanings: 
 

  WARNING: non observance may result in accident or injury. 

 

  ATTENTION: non observance may cause damage to the machine. 

 

  Information about the operation in progress. 

 

  OBSERVE: observation about the operation in progress. 

1.2.   RECOMMENDATIONS 

Technogym recommends the following steps for planning repair procedures: 
 

• 

Carefully evaluate the customer’s description of the machine malfunction and ask all the 
necessary questions to clarify the symptoms of the problem. 

 

• 

Clearly diagnose the causes of the problem. This manual provides the fundamental theoretical 
basis, which must then be integrated by personal experience and attendance at the training 
courses periodically offered by Technogym. 

 

• 

Rationally plan the repair procedure so as to minimize the downtime necessary for procuring 
spare parts, preparing tools, etc. 

 

• 

Access the component to be repaired, avoiding any unnecessary operations. In this regard it will 
be useful to refer to the disassembly sequence described in this manual. 

Содержание Recline Forma



























































































Отзывы: