Technogym Recline Forma Скачать руководство пользователя

Страница: 42 / 90

RECLINE EXCITE: Service & Maintenance Manual - rev. 1.1

Page 6.14

6.8. THE MACHINE DOES NOT READ THE TGS/SMART CARD

The machine displays this error if the TGS or Smart Card reader is not working properly, or if it is
not supplied by the digital plan board.

THE MACHINE DOES

NOT READ THE

TGS/SMART CARD

Does the supply v oltage

correctly reach the input to the

TGS/Smart Card reader?

Is the supply v oltage correct at

the input to the digital plan

board correct?

Replace cable CBQ-32

YES

Replace the digital plan

board

Is the serial communication link

between the digital plan board

and the TGS/Smart Card

reader OK?

Replace the digital plan board.

Is the communication link

between the digital plan board

and the TGS/Smart Card

reader OK?

Digital plan board

def ectiv e

YES

Replace the TGS/Smart

Card reader

Replace the TGS/Smart

Card reader

Follow the procedure step by step to correctly diagnose the problem. Take particular care with the
checks highlighted by circled numbers, which are described in detail below:

Содержание Recline Forma



























































































Результаты поиска

Содержание Recline Forma

Отзывы:

Похожие инструкции для Recline Forma

Бренды по названию

Популярные бренды

Technogym Recline Forma, Руководство по техническому обслуживанию

Результаты поиска

Содержание Recline Forma

Отзывы:

Похожие инструкции для Recline Forma

Бренды по названию

Популярные бренды