Technogel FREEZER 200/1 Скачать руководство пользователя страница 3

Страница: 3 / 49

Instructions for unpacking the machine

FREEZER 200/1 - GROSS WEIGHT 585 KG. NET WEIGHT 460 KG.

Remove all wood packing panels from the sides
and top

Lift the machine using a fork lift truck, inserting the forks
between the base of the machine and the bottom of the
crate

Unscrew the four bolts on the base of the crate which
hold the machine locked in position

CAUTION !

Once the bolts have been removed, the bottom of the
crate will detach from the machine base.

After removing the bottom of the crate, lower the fork lift
carriage and rest the machine on the ground.

THE TYPE OF WOOD USED FOR THE CRATE IS NATURAL PINE AND DOES NOT

CONTAIN ANY CHEMICALS WHATSOEVER. IT CAN THEREFORE BE RECYCLED

Содержание FREEZER 200/1


















































Результаты поиска

Содержание FREEZER 200/1

Отзывы:

Похожие инструкции для FREEZER 200/1

Бренды по названию

Популярные бренды

Technogel FREEZER 200/1, Инструкция по установке, использованию и обслуживанию

Результаты поиска

Содержание FREEZER 200/1

Отзывы:

Похожие инструкции для FREEZER 200/1

Бренды по названию

Популярные бренды