background image

TECH

 

 

 

TABLE OF CONTENTS 

I.

 

Safety ......................................................................................................................................................................... 3

 

ii.

 

Device description ..................................................................................................................................................... 4

 

iii.

 

Installation ................................................................................................................................................................. 4

 

iv.

 

How to use the  regulator ......................................................................................................................................... 7

 

1.

 

Principle of operation .............................................................................................................................................. 7

 

2.

 

Operation modes ..................................................................................................................................................... 7

 

v.

 

Main screen decription .............................................................................................................................................. 7

 

vi.

 

Regulator funktions – menu 1 ................................................................................................................................... 9

 

1.

 

Block diagram - regulator menu .............................................................................................................................. 9

 

2.

 

Clock settings ........................................................................................................................................................... 9

 

3.

 

Constant mode ...................................................................................................................................................... 10

 

4.

 

Pre-set day temperature  ................................................................................................................................ 10

 

5.

 

Day from… .......................................................................................................................................................... 10

 

6.

 

Pre-set night temperature ............................................................................................................................. 10

 

7.

 

Night from… ....................................................................................................................................................... 11

 

8.

 

Sensor hysteresis .............................................................................................................................................. 11

 

9.

 

Floor sensor ........................................................................................................................................................... 11

 

10.

 

Underfloor heating hysteresis  ...................................................................................................................... 12

 

11.

 

Maximum floor temperature  ......................................................................................................................... 12

 

12.

 

Minimum floor temperature .......................................................................................................................... 12

 

13.

 

Button lock ............................................................................................................................................................ 13

 

VII.

 

Regulator functions – Menu 2 ................................................................................................................................. 13

 

1.

 

Registration ........................................................................................................................................................... 13

 

2.

 

Built-in sensor calibration...................................................................................................................................... 13

 

3.

 

Floor sensor calibration ......................................................................................................................................... 13

 

4.

 

Software version.................................................................................................................................................... 14

 

5.

 

Default settings ..................................................................................................................................................... 14

 

VIII.

 

Technical data .......................................................................................................................................................... 14

 

 

 

JG. 24.02.2022 

 

 

 

Содержание EU-RI-1

















Отзывы: