background image

TECH

 

 

11 

 

7.

 

NIGHT FROM… 

 The  Night  from...  function  defines  the  exact  time  when  the  nighttime 
starts.  In  order  to  set  this  parameter,  press  MENU  button  until  the 
nighttime setting screen appears. Use PLUS and MINUS to set the hour 
and minute of night mode activation. Confirm by pressing MENU button 
(confirm  and  move  on  to  edit  the  next  parameter)  or  EXIT  button 
(confirm and return to the main screen view). Changes will also be saved 
automatically after 5 seconds of inactivity. 

 

8.

 

SENSOR HYSTERESIS 

Room temperature hysteresis defines the pre-set temperature tolerance in order to prevent undesired oscillation in case 
of small temperature fluctuation (within the range of 0,2 ÷ 5°C). 

Example: 

Pre-set temperature:  23°C 
Hysteresis:  1°C 
 

 The room regulator reports that the temperature is too low when the 
room temperature drops to 22 °C. 

In order to set the hysteresis, press MENU until the hysteresis settings appear on the screen.  

Use PLUS and MINUS to set the desired hysteresis value. Press MENU to confirm and move on to the next parameter or 
press EXIT to confirm and return to the main screen view.  Changes will also be saved automatically after 5 seconds of 
inactivity. 

9.

 

FLOOR SENSOR 

In order to enable or disable the floor heating, press the MENU button 
until the floor heating screen appears.  

In  order  to  enable  the  floor  heating,  press  PLUS  button  (  ON  will  be 
displayed on the screen).  

In order to disable the floor heating, press MINUS button ( OFF will be 
displayed on the screen). To confirm, press MENU button  (confirm 
and go on to edit the next parameter) of EXIT button (confirm and 
return to the main screen view). Changes will also be saved 
automatically after 5 seconds of inactivity. 

NOTE 

 

Correct operation of a regulator with a floor sensor is possible 
only in the mode 

RS REGULATOR

 → 

STANDARD 

REGULATOR

 

When the floor sensor is enabled, make sure that the minimum 
valve opening in the controller (EU-I-2, EU-I-2 Plus, EU-I-3, EU-
I-3Plus)  is set at the minimum of 5% or more.  

Содержание EU-RI-1

















Отзывы: