LC-Display
Page
Controls & Connectors
2 - 3
LC-Display .
19
Setting up the TEAM TeCom-508
Removing and mounting of the belt clip
19
Inserting the batteries
19
Operation of the TEAM TeCom-508
I. Directly accessible functions
1) Switching On/Off
20
2) Battery level indicator
20
3) Volume level adjustment
20 - 21
4) Disabling the noise suppression
21
5) Voice transmission
21
6) Call melody transmission
21
7) LCD window illumination
22
8) Key lock function
22
9) Channel scan function
22
10) Socket for external accessory
22
11) Charging the accumlator pack with the charger
23
II. Menu-activated functions
1) Channel selection
23
2) CTCSS function
24
3) Scrambling function
24 - 25
4) Selection of the call melody
25
5) Monitoring function
25 - 26
6) Dual watch function
26 - 27
7) VOX function
27 - 28
8) Atomatic-Power-Off function
28
9) Stop-watch function
28 - 29
Additional Information
1) Safety
29
2) Service
29
3) Conformity
30
4) Technical Data
30
19
English
English
Table of Contens
Unpack carefully your ScramTalk-808 package and check whether the supplied mate-
rial matches with the items listed below. In case of loss or damage of a part contact
your carrier at once:
2 sets ScramTalk-808
2 accumulator packs
1 foldable double desktop charger
1 AC mains adaptor
1 multilingual operation manual
18
Battery indicator
Dual Watch function
Unit is transmitting
Squelch is open
Channel number indication
CTCSS tone code
number indication
VOX function
Internal reception of a
signal without detecting
a CTCSS code
Babysitter function on
the baby’s side
Call tone melody
Babysitter function on the
parent’s side
Stop watch
Scrambling function
Autmatic-Power-Off function
Channel scan function
Setting up the TEAM ScramTalk-808
1) Removing and mounting of the belt clip
To remove the belt clip, turn the rear panel toward you. The latch of the belt clip ( 17 ) is loca-
ted near the headset socket SP./MIC ( 16 ). Pull the latch with your fingernail towards you and
hold it. Then, by pulling the belt clip towards the top of the antenna remove the belt clip ( 17 ).
To insert the belt clip, push the notch of the clip into the notch on the rear panel of the unit. Then
push the clip towards the unit’s bottom side until the belt clip latches.
2) Inserting the batteries or the accumulator pack
Turn the unit that way that the rear panel lies in front of you. Remove the belt clip ( 17 ). The
locking of the battery compartment lid ( 14 ) is located at the bottom side of the unit. To open
the battery compartment you have to push the locking away from the lid and turn it down. Then
you can take the lid off.
Now insert 3 alkaline or rechargeable AAA ( = Micro ) cells into the battery compartment accor-
ding to the polarity signs inside. If you use rechargeable cells we recommend the NiMH type. If
you use one of the accumulator packs follow the instructions which are written on its back. Ins-
ert it in that way into the unit, that the label on the rear side remains visible, and the arrow “UP”
is pointing upwards. Please take also care that the plastic strip of the accumulator pack is
accessible. This simplifies a later removal of the accumulator pack.
To close the battery compartment put the lid ( 14 ) onto the compartment in that way that the
two guide bolts at the top of the lid grip into the corresponding guide holes at the top of the bat-
tery compartment.
Finally secure the lid by pushing the locking on it until it snaps in.
ScramTalk-808 manual 15.06.2004 12:55 Uhr Seite 18
