30
31
4) You can select a channel to make a call by pressing the PTT button
during anytime of scanning.
5) Press again the button set as Scan or Scan + Temporarily Delete to
end scanning.
6.5 Priority Scan
During scanning, if the priority channel has been set on the radio,
when the priority channel receives a signal the radio will automatical-
ly switch to the priority channel even the normal channel is receiving
signals at that time. And the radio will stay on the priority channel till
that signal disappears. The dealer can set the delay time between sig-
nal disappearing and continuing scanning.
6.6 Temporarily Delete
When scanning pauses on a channel, press and hold the button pro-
grammed as Temporarily Delete or Scan + Temporarily Delete for
1 second to delete this channel temporarily from the scanning list.
Note:
The priority channel cannot be deleted. And when the number of scan-
ning channels is less than 2, you cannot delete any channel, either.
After exiting scanning mode and entering it again, the temporarily
deleted channel will be added in the scanning list again.
6.7 CALL1/CALL2
Press and hold the PTT button, and then press the side button pro-
grammed as CALL1 or CALL2 to send the stored 5Tone code.
Release CALL1 or CALL2 button, and speak to the microphone to call
with the PTT button still pressed.
7 VOX
VOX function enables you to use the radio without manual operation.
This function can only be set by the dealer and you a specified ear- /
microphone as to be connected to the radio.
Before using VOX, you must set VOX gain level. Such setting enables
the radio to identify the voice volume. If the microphone is too sensi-
tive, the background noise will trigger the radio to transmit. If the
microphone is not sensitive enough, it cannot receive your voice when
you speak. Make sure to adjust VOX gain level to proper sensitivity.
1) Connect the ear- / microphone with the radio.
2) Turn off the radio. Then, turn it back on, while pressing Side Button
1 at the same time.
3) Hold Side Button 1 till a beep sounds and LED lights orange. Then,
release Side Button 1, and the radio will announce VOX gain level.
4) Press Side Button 1 to increase VOX gain level; press Side Button 2
to decrease it.
VOX gain level can be adjusted between level 1 and level 10 and
OFF. When adjusting gain level, the radio will announce VOX gain
level. If OFF is selected, beep tone will sound.
5) Press PTT to store the setting. After a beep, the radio announces
new VOX gain level.
6) Turn off the radio, and turn it on again, and then VOX function is
activated.
8 Clone Mode
The dealer can turn on or turn off this function by programming. You
can transmit set-up data to or from another radio. Press the PTT but-
ton and Side Button 2 for 2 seconds, and turn on the radio at the same
time entering Clone Mode.
1) When the sub radio entering clone mode, LED lights orange and
you will hear voice annunciation Clone . When release buttons,
voice annunciation Channel 1 sounds.
2) When the host radio entering clone mode, LED lights orange and
you will hear voice annunciation Clone . When release buttons,
voice annunciation Channel 1 sounds.
3) Select on the host radio the channel number identical with that on
the sub radio. You can select clone channel by pressing Side But-
ton 1 or Side Button 2.
4) Press the PTT button on the host radio to transmit data and LED
flashes red. Sub radio begins to receive cloning data and LED lights
green. When the data transfer is completed, the host radio sounds
confirming beep.
5) Then host radio cannot be set as sub radio.
6) The cloning rate has been set to a low value 1200 bps.
9 Emergency Alert
If Emergency Alert has been set on the radio by programming, you can
make emergency calls.
1) Press and hold the emergency alert button. According to the delay
time preset on the radio, the time required for holding the button
may be different. When the radio enters emergency call mode, it will
switch to the emergency channel automatically, and starts transmit-
ting according to the dealer's setting. Transmitting and receiving
recycle can be set by your local dealer.
2) To exit the emergency call mode, press again and hold the emer-
gency call button. If the repeating times of emergency call has
expired, the radio exit emergency call mode automatically and
returns to normal operation mode.
10 Auxiliary Functions
10.1 Time-out Timer (TOT)
Time-out timer can prevent any caller from occupying one certain
channel for an extended period of the time.
If the radio is continuously transmitting longer than the time preset by
the dealer, the radio will stop transmitting and warning tone sounds,
and please release the PTT button.
The dealer can program that the warning sounds earlier than TOT
action.
GB
GB
pt-6200.qxp 03.05.2006 14:11 Seite 31
