Team Assocciated RC10 B3 Basic+ Скачать руководство пользователя

Страница: 25 / 25

.-)674-5

See page 2 for complete specs on what is included in each kit.

Factory Team Kit shown. Radio and electronics are not included in kits.

Rear Pro-Line “Holeshot M2” tires

Front Pro-Line “4 Rib M2” tires

Adjustable battery placement

Hard-anodized,

PTFE

-coated gray shocks

(Team and Factory Team kits only)

MIP CVD axles (Team and
Factory Team kits only)

Molded composite chassis (Basic, Sport and Team kits only).
Graphite chassis, towers and arms (Factory Team kits only)

Adjustable caster,
camber, toe-in

Extra-long suspension
arms, front & rear

2.40:1 transmission

Motor (Basic
Plus & Sport
kits only)

Factory Team performance parts

Reedy Modifieds motors & batteries

LRP digital speed controls

TEAM ASSOCIATED RECOMMENDS

Содержание RC10 B3 Basic+


























Результаты поиска

Содержание RC10 B3 Basic+

Отзывы:

Похожие инструкции для RC10 B3 Basic+

Бренды по названию

Популярные бренды

Team Assocciated RC10 B3 Basic+, Инструкция по сборке и руководство пользователя

Результаты поиска

Содержание RC10 B3 Basic+

Отзывы:

Похожие инструкции для RC10 B3 Basic+

Бренды по названию

Популярные бренды