Team Assocciated RC10 B3 Basic+ Скачать руководство пользователя | Manualshive

Страница: 23 / 25

background image

REMOVE THESE
PARTS FOR:

Steps 1-2

Basic & Sport ONLY
9490Y, qty pr
1 piece rear wheels

Team & F.T. ONLY
9491, qty pr
Pro-Line rear wheels

6825, qty 2
Holeshot rear tire

9490Y

or 9491

3438, qty 2
8-32 locknut

fit notch of wheel

over roll pin

T E A M K I T O N L Y

Basic & Sport ONLY
9480Y, qty pr
1 piece front wheels

Team & F.T. ONLY
9482, qty pr
Pro-Line front wheels

6878, qty 2
M2 front tire

Basic & Sport ONLY
6599, qty 4
3/16 x 3/8
unflanged bushing

6222, qty 2
4-40/5-40
locknut

1:1

1:1

1:1

6825

3438

FRONT WHEELS AND TIRES
Make a 1/8" hole in the wheel.
Install the #6878 tire to the #9480Y or #9482 wheel.
Glue the tire to the wheel with super glue (cyanoacrylic glue) in four
spots around the tire on both sides.

WARNING! Follow the adhesive

manufacturer's instructions for proper use and safety. Wear eye and
hand protection.

Insert the #6599 bushings or #3799 bearings into both sides of the front
wheel.
Install wheel onto axle. Thread on #6222 locknut. Finish second front
wheel and tire.

9481Y

or 9482

6878

6599

or 3977

6222

REAR WHEELS AND TIRES
Make a 1/8" hole in the wheel. Make sure foam insert is centered
in tire.
Install the #6825 tire to the #9490Y or #9491 wheel.
Glue the tire to the wheel with super glue (cyanoacrylic glue) in
four spots around the tire on both sides.

WARNING! Follow the

adhesive manufacturer's instructions for proper use and safety.
Wear eye and hand protection.

Install wheel onto axle, lining up roll pin with slot in the wheel.
Thread on the #3438 locknut. Finish second rear wheel and tire.

T O O L S U S E D

s t e p 1

24

3/32"

s t e p 2

make a 1/8" hole

make a 1/8" hole

B A G I

Team & F.T. ONLY
3977, qty 4
3/16 x 3/8
unflanged ball bearing

1:1

6599

or 3977

«
...
21
22
23
24
25
»

Содержание RC10 B3 Basic+


























Отзывы:

Нет отзывов

Похожие инструкции для RC10 B3 Basic+

Aprilia Dorsoduro 900

Бренд: Jamara Страницы: 12

Бренд: Jamara Страницы: 8

Бренд: Carson Страницы: 48

CE-10 Desert Quad 50 040 4012

Бренд: Carson Страницы: 72

Бренд: Yokomo Страницы: 16

Бренд: Yokomo Страницы: 36

Бренд: Yokomo Страницы: 32

Бренд: Team Страницы: 33

Бренд: Team Assocciated Страницы: 30

540070 MONSTER BUGGY

Бренд: T2M Страницы: 30

Бренд: Peg-Perego Страницы: 52

Power Wheels X0071

Бренд: Fisher-Price Страницы: 28

POWER WHEELS W6203

Бренд: Fisher-Price Страницы: 32

Бренд: Retro Roller Страницы: 2

Бренд: Retro Roller Страницы: 4

Бренд: Kyosho Страницы: 48

Inferno neo ST Race Spec

Бренд: Kyosho Страницы: 32

Бренд: Traxxas Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды