Team Assocciated RC10 B3 Basic+ Скачать руководство пользователя | Manualshive

Страница: 11 / 25

background image

s t e p 1
L E F T S I D E

12

6370

6372

6374

6273

6272

7260

7360

7360

6388

6374

6375

6466
1/16"

6273, qty 2
ball end

B A G E

1 : 1

1:1

HUB CARRIERS TO REAR ARMS
(Upper left drawing:) Push the #9273 spacer into the outdrive of the
transmission.
(Upper left drawing:) Insert the dogbone pins into the stub axle and
outdrive hub as shown.
Place the hub carrier between the arm holes as shown and add two
#6466 spacers where shown.
Add one #6299 E-clip to the end of the #9263 hinge pin, insert it as
shown, then add the other #6299 E-clip.
Now install the axle assembly for the right side.

ASSEMBLE REAR HUB CARRIERS
Note that the #7366 hub carriers are marked for left and right.
Insert #7360 bushings into each side of the left hub carrier.
Install the #6374 stub axle as shown.
Insert #6388 cone washer as shown, raised outer edges facing
out. Add #6375 roll pin.
Insert the #6372 spring into the stub axle.
Thread on the #6273 ball end and add the #7260 nut to the
other side.

(When you do the other hub carrier, thread the ball

end into the other side so both will point to the front when
assembled.)

Add a #6272 dust cover to the ball end.

Follow the above for the right hub carrier.

6272, qty 2
dust cover

1:1

1:1

1:1

1:1

1:1

1:1

1:1

1:1

1:1

6299, qty 4
E-clip

6466, qty 4
spacer, 1/16"

7260, qty 2
small nut

7366, qty 2
hub carrier

1:1

9263, qty 2
rear outer hinge pin

6375, qty 2
roll pin

9273, qty 2
dogbone spacer
3/32" (black)

6388, qty 2
cone washer

7360, qty 4
bushing

6370, qty 2
dogbone

6372, qty 2
dogbone spring

6374, qty 2
stub axle

T O O L S U S E D

9273

3/32" (black)

REMOVE THESE
PARTS FOR:

Basic: step 1

Sport: step 1

B A S I C & S P O R T K I T S O N L Y

B A S I C & S P O R T K I T S O N L Y

9257

6299

9263

6299

9263

R E A R

7366

6466
1/16", 2

make sure window

faces front

5

7366

10

«
...
9
10
11
12
13
...
»

Содержание RC10 B3 Basic+


























Отзывы:

Нет отзывов

Похожие инструкции для RC10 B3 Basic+

Бренд: LaTrax Страницы: 36

Бренд: Sabre Страницы: 22

Бренд: DICKIE SPIELZEUG Страницы: 16

Бренд: Serpent Страницы: 12

Бренд: Serpent Страницы: 20

Бренд: Shopify Страницы: 10

Бренд: Maverick Страницы: 52

Бренд: Advanced Racing Technologies Страницы: 16

Бренд: Electrix RC Страницы: 18

Бренд: Element Страницы: 30

Бренд: Corally Страницы: 24

Бренд: Quer Страницы: 44

90mm Viper EDF EPO

Бренд: HSDJets Страницы: 8

Бренд: Eaelec Страницы: 2

Бренд: Jamara Страницы: 12

Бренд: Ofna Racing Страницы: 45

Бренд: rastar Страницы: 38

Бренд: Yokomo Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды