background image

408-6788

3

 of 12

Rev 

L

1. Consult latest issue of MIL-C-39012 and QPL for current military dash numbers.

2. All items are included in Kit 59981-1, except those marked with ‡

† For both N Series and TNC Series

Figure 2 (End)

CONNECTOR TYPE FOR

RG-405 CABLE

PART NUMBERS

1

TE

CATEGORY B

CATEGORY F

HAND TOOL 59980-1

Military 

M39012/

TE

Military 

M39012/

TE

Dies

2

Locator

2

Plug with Center Contact

---

79B3103

227868-1

79-3307

228639-1

312253-2

220221-2

Plug with Center Contact and 

Safety Wire Holes

228639-4

---

---

79-3207

228639-3

312253-2

220221-2

Short Plug with Center Contact

221447-1

221447-2

---

---

---

---

313113-1‡

220221-3‡

Short Plug with Center Contact 

and with Safety Wire Holes

221447-3

221447-4

---

---

---

---

313113-1‡

220221-3‡

Sealed Short Plug

221812-1

---

---

---

---

313113-1‡

220221-3‡

Sealed Short Plug with Safety 

Wire Holes

221812-2

---

---

---

---

313113-1‡

220221-3‡

Short Plug with Retractable 

Collar

221447-5

---

---

---

---

313113-1‡

220221-3‡

Right-Angle Plug

228583-2

---

---

80-3307

228583-1

312253-2

312173-1‡

Right-Angle Plug with Safety 

Wire Holes

228583-4

---

---

80-3207

228583-3

312253-2

312173-1‡

Sealed Right-Angle Plug

222264-1

---

---

---

---

312253-1

312173-1

Sealed Right-Angle Plug with 

Safety Wire Holes

222264-2

---

---

---

---

312253-1

312173-1

Jack

228640-2

---

---

81-3207

228640-1

312253-2

220222-2

4-Hole Panel Jack

---

82B3003

227870-1

82-3207

228641-1

312253-2

220222-2

Bulkhead Jack

227871-3

228642-2

83B3003

227871-1

83-3207

228642-1

312253-2

220222-2

TNC Series Connector:

Rear-Mounted Jack

228507-1

---

---

---

---

312253-2

220222-2

Adapter Assembly

(For TNC Series Only)

228505-1†

---

---

---

---

312253-2

220222-2

Содержание 59981-1














Отзывы: