TDT BH32 Скачать руководство пользователя страница 8

17-24

System 3

BH32 Behavioral Cage Controller

To make changes to the configuration:

Type or select the desired values then click the 

Save Config 

button. The 

Save Config button saves the current configuration settings and performs a 

soft reset of the BH32 interface to load the settings.

To restore the default values:

Click the 

Reset to Defaults

 button.

Network

 

Configuration

 

Page

Note:

This page may require authentication. See “Username and Password” on page 17-

22, for more information.
The BH32’s IP Address, host name and web username and password can be 

changed on this page.

If the Enable DHCP check box is checked, the 

IP Address

Gateway

 

Address

Subnet Mask

, and 

DNS

 server address values are overridden and automatically 

configured by the DHCP server if available.

Note:

These settings are reserved for connections that cannot locate a DHCP server. If no 

DHCP server can be detected, contact your network administrator for applicable 

settings.

To change the username and password:

1. Enter the desired new username and password in the 

Web User Name

 and 

Web Password

 boxes.

2. Click the 

Save Config

 button.

Note:

 Once changed, you may need to re-enter the new username and 

password to access pages that require authentication, such as the Network 

Configuration or Setup pages.

Содержание BH32

















Отзывы: