TDT BH32 Скачать руководство пользователя страница 2

17-18

System 3

BH32 Behavioral Cage Controller

Important!

The two External Power Molex connectors on the top panel are shorted together; do 

not use more than one external power source. The second external power connector 

can be used to jumper the external power source to another BH32

Voltage

 

Mode

 

Toggle

This back panel switch toggles between 5 V and external power supply source for all 

Molex output banks. Use 5 V mode for connections to mains power or PoE. Use 

External Voltage mode for other external power sources up to 30 V.

Power

 

Switch

The On/Off toggle switch turns the BH32 power off or on. The LED display will be 

illuminated when the power is on.

Status

 

Display

The front panel display screen reports system status. The Mode button to the left 

toggles the display modes. 

The display modes include:

1. Device Number - how the BH32 is recognized on the network by other 

devices

2. Bank Status - bank direction and current state of all bits in each bank
3. NetBIOS name and IP address:
4. IP address of paired RZ device (if paired). See “RZ Configuration” on 

page 17-22.

Push and hold the Mode button for two seconds then release to automatically cycle 

through all of the display items, displaying each for one second.
Push and hold the Mode button for 10 seconds to reset the Device Number.

I/O

 

Control

The BH32 is a net appliance that was designed to be used under a variety of 

conditions, not all of which are available from vendors of behavioral control systems. 
At the most basic the TDT BH32 system can replace existing devices such as the 

Med Associates, Colburn or Lafayette systems that interface to a standard operant or 

behavioral box with input and output lines, where the output lines drive feeders, lick 

meters and other devices that require more than a digital trigger. At the more 

complex level the TDT system can be used to send and receive complex signals to 

control multiple hardware devices. 

Power Source

Mode

Max Total Output

Mains power

5 V

200 mA

PoE

5 V

100 mA

External power up to 30 V

External Voltage

3 A

Содержание BH32

















Отзывы: