TDT BH32 Скачать руководство пользователя страница 5

System 3

17-21

BH32 Behavioral Cage Controller

on the PC Ethernet interface. In such cases, the IP address of the BH32 must be 

used instead.

Configuration

 

through

 

the

 

Web

 

Interface

Every BH32 contains a minimal web server which is used for configuration and 

monitoring. Options can be set here if no DHCP server is available. If a DHCP 

server exists, the NetBIOS name associated with the dynamically assigned IP address 

can be configured using the BH32 server.

To connect to the BH32 server:

Make sure there is an active connection from the PC to the Ethernet port on the 

back of the BH32 then open an Internet browser such as Internet Explorer, Chrome 

or Firefox.

Enter the device’s IP address as the web address (e.g. http://10.1.0.100) 

and press 

Enter

.

or 

Enter the NetBIOS name as the web address (e.g. TDT_BHC_32_1001) 

and press 

Enter

.

Once connected, navigation to the BH32 web interface loads the Welcome page. 

Clicking the links to the left of the web interface loads the corresponding page.

Welcome

The Welcome page provides basic information, allows real-time control of the BH32, 

and provides feedback on the status of each Bank.

Device

 

Box

The status of individual bits is displayed for each bank. Clicking bits on an Output 

bank (red 0 or 1) will toggle that output bit and the corresponding LED on the 

front panel of the BH32. This can be used to manually control the output of the 

BH32 for testing a device connected to that output.

Содержание BH32

















Отзывы: