1
RFE 1000 SERIES INSTRUCTION MANUAL
RFE1000 SERIES SPECIFICATIONS
RFE1000-24
RFE1000-32
RFE1000-48
1
Rated output voltage
V
24
32
48
2
Output voltage set point
V
24+/-1%
32+/-1%
48+/-1%
3
Output voltage range
V
21.5-29
28.8-38.4
43-58
4
Maximum Output Current (Refer to Fig.1)
A
40
31
21
5
Maximum output power
(*9)
W
960
992
1008
6
Input voltage / frequency range
(*1)
-
85~265Vac continuous, 47~63Hz, Single phase
7
Maximum input current (at 100/200Vac)
A
12.0/6.0
8
Power Factor (Typ) (at 115/230V)
-
>0.98 at maximum output power
9
Efficiency (Typ)
(*2)
%
86/88%
86/88%
87/89%
10
Inrush current
(*3)
A
Less than 40A
11
Hold-up time
mS
20mS typical at 100Vac input, rated output voltage and less than 80% of rated load
12
Maximum line regulation
(*5)
-
0.40%
13
Max load regulation
(*6)
-
0.80%
14
Output Ripple and noise P-P
(*4)
mV
200
250
300
15
Temperature stability
-
0.1 % of rated Vout for 8hrs after 30mln warm-up. Constant line. load and temperature.
16
Temperature coefficient
PPM/°C
200
17
Remote sensing
(*7)
-
Possible. Refer to Instruction Manual.
18
Parallel operation
-
Possible. Refer to Instruction Manual.
19
Series operation
-
Possible. Refer to Instruction Manual.
20
Over current protection
-
105--125% of maximum output current. Refer to Fig. 1
21
Over voltage protection
(*8)
V
31~34
41.5~45.5
62~66
22
Over temperature protection
-
Inverter shut down method, automatic recovery.
23
Remote On/Off control
-
By electrical signal or dry contact. ON: 0~0.6V or short. OFF: 2~15V or open.
24
DC OK signal
-
Open collector signal. On when Vout>80+/-5% rated output. Max.sink current: 10mA
25
Over-Temp. warning
-
Open collector signal. Refer to Instruction Manual
26
AC fail signal
-
Open collector signal. Refer to Instruction Manual
27
Auxiliary power supply
-
11.2~12.5VDC. 0.25A Maximum output current.
28
Vout voltage trimming
-
Possible, via Vout Trim Potentiometer on PCB. Refer to Instruction Manual.
29
Front panel indicator
-
DC OK. Refer to Instruction Manual.
30
I²C Interface
-
No
31
Operating temperature
-
0~50°C: 100% load.
+50°C to +60°C: Derate 2%/°C of load
+60°C to +70°C: Derate 2.5%/°C of load
32
Storage temperature
-
-30....85°C
33
Operating humidity
-
10-90% RH, no condensation.
34
Storage humidity
-
10-95% RH, no condensation.
3S
Cooling
-
By internal Fans. Variable speed control.
36
Vibration
-
Built to meet ETS 300 019
37
Shock
-
Built to meet ETS 300 019
38
Conducted emission
(*10)
-
Built to meet EN55032B, FCC part 15J-B, VCCI-B
39
Radiated emission
-
Built to meet EN55032B, FCC part 15J-B, VCCI-B
40
Applicable safety standards
-
UL60950-1, EN60950-1
41
Withstand voltage
Input-Output:
Input-Ground:
Output-Ground:
-
3000Vrms, 1min.
2000Vrms, 1min.
500Vrms, 1min.
42
Insulation resistance
-
More than 100Mohm at 25°C and 70% RH. Output-Ground: 500Vdc
43
Leakage current
mA Less Than 1.1 mA at 230Vac
44
Weight (Typ)
Kg
2.0
45
Size (W*H*D)
-
127x41 x305 mm. Refer to Outline Drawing.
Notes:
*1: For cases where conformance to various safety standards (UL, EN etc.) is required.
to be described as 100-240Vac (50/60Hz).
*2: At 100/200Vac, rated load and 25°C ambient temperature.
*3: Not applicable for the noise filter inrush current less than 0.2mS.
*4: Measured with JEITA RC-9131A 1:1 probe, 20MHz B.W.
*5: From 85-132Vac or 170-265Vac, constant load.
*6: From No-load to Rated load, constant input voltage. Measured at the sensing point in Remote sense.
*7: Remote sensing can compensate up to 1V drop on each load wire.
*8: Inverter shut down method. Reset by AC voltage recycle or by On/Off control.
*9: Derate Maximum output power by 10% for input voltage less than 95VRMS
*10 RFE1000 series considered as professional equipment and not intended for sale to general public.
Model
V/I
RFE1000 -24
RFE1000 -32
RFE1000 -48
V1 (V)
24
32
48
V2 (V)
29
38.4
58
I1 (A)
33
26
17.25
I2 (A)
40
31
21
Fig. 1: Rated output current vs output voltage
Vout (V)
Iout (A)
I1
V1
V2
I2
Содержание RFE1600-12
Страница 15: ...3 RFE1000 SERIES OUTLINE DRAWING...
Страница 18: ...6...
Страница 23: ...11...
Страница 24: ...12 IA714 04 01C...