TCS ISW3030 Скачать руководство пользователя страница 10

Страница: 10 / 16

07/2015

TCS TürControlSysteme AG, TCS Hotline Germany: +49 (0) 41 94/ 9 88 11 88

Subject to technical changes.

Mail: [email protected]

ISW3030-0140 UK 2 A

Commissioning



Install the devices of the system voltage-free and completely.



Proof the a-, b- and P-wire against each other on short-circuit.



Switch on the main voltage.

Hint:
If the floor push button is not working, proof, if it is connected to the a-wire of the power
supply and control unit.

Settings

Pre-adjusted times

communication time

max. 2 min

flashing period of the green LED, if the voice
channel is busy after the voice communication
is established

2 sec

3 x flashing

internal standby time, if the device is calling or
is called

around
30 sec

2-wire/3-wire opration

The jumper J1 is adjusted for the 2-wire
operation in delivered state.

2-wire operation (delivered state)



Put the jumper J1 at both contacts for the

3-wire operation.

3-wire operation

Содержание ISW3030

















Результаты поиска

Содержание ISW3030

Отзывы:

Похожие инструкции для ISW3030

Бренды по названию

Популярные бренды

TCS ISW3030, Информация о продукте

Результаты поиска

Содержание ISW3030

Отзывы:

Похожие инструкции для ISW3030

Бренды по названию

Популярные бренды