TC Electronic Mastering 6000 Скачать руководство пользователя | Manualshive

Страница: 26 / 33

background image

MAIN FRAME - FRONT & REAR PANEL

POWER ON

MAINFRAME/SYSTEM 6000

FLOPPY DRIVE

POWER

PC CARD

System 6000 Mainframe Front

Power Key

Switches power On/Off.

3.5” floppy disc slot

For storing presets and event-lists and for loading software-
upgrades.

System 6000 Mainframe Rear

I/O Slot A

I/O Slot B/AES-8

DSP Slot

I/O Slot C

DSP and I/O Slots A, B and C

These slots are used for I/O cards ADA 24/96 and AES-8.
Slots must be filled consecutively in alphabetic order.
The System 6000 DSP card fits the DSP slot only. When
I/O cards are mounted, dip switches on the cards must be
set accordingly.
An AES-8 card should be installed in “I/O Slot B/AES-8”
only. If you Mainframe rear panel carries a label saying
BUS updated you can install the AES-8 card yourself -
Please refer to the full manual.
If your Mainframe serial number is below 285580 and no
“BUS-updated label” is present on the rear-panel, a
Mainframe hardware update performed by an authorized
TC Service center is necessary before installation.

For further information contact:
TC Headquarters : [email protected]

+45 87427000

US Customer

: [email protected]

001 805 373 1828

Power In

100-230V AC. 50/60Hz - auto-select.

SMPTE

1/4” connection for SMPTE sync. Input.

Ethernet/LAN

Connection for external control devices e.g. the TC Icon.
The type is 32 bit PCI Ethernet interface fully compliant
with IEE 802.3u 10/100 Mbps CSMA/CD standards.

The connector type is a 100Base-T RJ-45 (CN13)

Ground Lift

Use this standard chassis ground lift if you encounter
problems with hum.

MIDI In, Thru and Out

5 pin DIN connectors.

Remote

This connection is for service and test purposes only.

GPI

General Purpose Input. Connect a TC Master Fader or a
tip-to-ground switch. Applications vary depending on the
specific algorithm.

Rackmounting Advice

• The Mainframe 6000 should not be placed in an

environment with a temperature exceeding 50 degrees
celsius.

• Do not cover the ventilation openings on the sides of the

frame.

The cooling fan is activated according to the
temperature inside.

PCMCIA slot

For future software facilities and handling of additional
preset banks.

Power On LED

During start-up this LED is red. When the unit is ready for
use, the LED will turn green.

BUS updated - label

26

«
...
24
25
26
27
28
...
»

Содержание Mastering 6000


































Отзывы:

Нет отзывов

Похожие инструкции для Mastering 6000

Бренд: ParaBody Страницы: 4

Бренд: Cadman Страницы: 66

Бренд: Califone Страницы: 7

Бренд: CALITEK Страницы: 16

Бренд: LAHTI PRO Страницы: 20

Бренд: LAHTI PRO Страницы: 16

Бренд: J&M Страницы: 53

Бренд: Qazqa Страницы: 2

Бренд: Jackco Страницы: 6

Бренд: KaVo Страницы: 49

Бренд: Easson Страницы: 33

Бренд: Launch Страницы: 3

Бренд: Launch Страницы: 43

Бренд: Launch Страницы: 8

Бренд: Launch Страницы: 67

Бренд: Launch Страницы: 55

Бренд: LAUNCH TECH Страницы: 14

X-431 PROS V4.0

Бренд: Launch Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды