TBS GEMINI Mini FPV Hex Скачать руководство пользователя страница 24

Страница: 24 / 56

TBS CORE

The TBS CORE PNP25 included in the kit is mounted behind the pilot camera and provides voltage regulation

to the video transmitter and pilot camera, in addition to an On-Screen Display (OSD) overlay for crucial flight

data (mAh current consumption, battery voltage, flight timer, receiver signal).

An optional TBS PNP PRO upgrade can provide additional details such a home direction, speed and location.

Menu configuration

The CORE PNP25 has a configuration menu which can be entered by holding down the ENTER button on the

front side of the unit for 3 seconds - use the UP and DN buttons to toggle between the options. Use a plastic

spudger to reach the buttons if needed.

The setup menu allows you to configure several aspects (recommended settings highlighted in bold):

●

RSSI

- Received signal strength - off, analog, digital or link (EzUHF), set min. and max. signal level

●

CURR. TYPE

- Current sensor - 25A or 50A

●

CAM. TYPE

- Camera type - FPV or GoPro (avoids OSD overlapping)

●

BATT ADJUST

- Battery voltage adjust - tune the OSD battery voltage reading

●

OSD

- On-Screen Display - on or off for a completely immersive experience

●

EXIT

- Exit out of the menu

Содержание Mini FPV Hex

























































Результаты поиска

Содержание Mini FPV Hex

Отзывы:

Бренды по названию

Популярные бренды

TBS GEMINI Mini FPV Hex, Руководство пользователя

Результаты поиска

Содержание Mini FPV Hex

Отзывы:

Бренды по названию

Популярные бренды