Taylor Taylormate 150 Скачать руководство пользователя страница 28

Страница: 28 / 77

Troubleshooting Guide

Models 150, 152, 162, 168

General Troubleshooting

PROBLEM

PROBABLE CAUSE

REMEDY

No product being dispensed.

a. The power switch is in the “OFF”

position.

a. Place the power switch in the

“AUTO” position.

b. The mix level is inadequate in the

mix hopper.

b. Fill the mix hopper with mix.

c. The beater motor overloaded.

c. Reset the freezer.

d. The unit is unplugged at the wall

receptacle.

d. Plug in the power cord. Press the

push-button switch.

e. The circuit breaker is tripped or

the fuse is blown.

e. Place the circuit breaker in the

“ON” position, or replace the
fuse. Press the push-button
switch.

f. The freezer door is incorrectly

assembled.

f. See the Operator’s Manual for

proper assembly.

g. Product is being drawn off in

excess of the freezer’s capacity.

g. Stop drawing product and allow

the unit to recover.

The machine will not operate in
the “AUTO” mode.

a. The unit is unplugged.

a. Plug in the power cord; press the

push-button switch.

b. The refrigeration system is not

activated.

b. On T.Q.C. units, momentarily

raise the draw switch to activate
the refrigeration system.

c. The circuit breaker is tripped, or

the fuse is blown.

c. Place the circuit breaker in the

“ON” position, or replace the
fuse. Press the push-button
switch.

d. The beater motor overloaded,

causing a loss of power to the
power switch.

d. Reset the freezer.

The product is too stiff.

a. The temperature control or the

T.Q.C. is set too cold.

a. Adjust the temperature control.

Do not set the temperature
colder than 18

F (

−

C).

The product is too soft.

a. The temperature control or the

T.Q.C. is set too warm.

a. Adjust the temperature control.

b. The air tube is not installed.

b. Install the air tube in the mix inlet

hole at the bottom of the mix
hopper.

c. Out-drawing the freezer’s

capacity.

c. Two 4 oz. (113.4 gram) servings

in one minute.

The freezing cylinder walls are
scored.

a. Operating freezer without the front

bearing on the freezer door.

a. Install the front bearing on the

freezer door.

b. The gear unit or the direct drive is

out of alignment.

b. Align the gear unit or the direct

drive.

Содержание Taylormate 150














































































Результаты поиска

Содержание Taylormate 150

Отзывы:

Похожие инструкции для Taylormate 150

Бренды по названию

Популярные бренды

Taylor Taylormate 150, Руководство по обслуживанию

Результаты поиска

Содержание Taylormate 150

Отзывы:

Похожие инструкции для Taylormate 150

Бренды по названию

Популярные бренды