Taylor Taylormate 150 Скачать руководство пользователя страница 13

Страница: 13 / 77

Models 150, 152, 162, 168

Introduction

General Installation Instructions

The following are general installation instructions. For

complete installation details, please see the checkout

card.

Site Preparation

Review the area the unit is to be installed in before

uncrating the unit. Make sure that all possible hazards

the user or equipment may come into have been

addressed.

Clearance: Air Cooled Units

Please see the “Model Specifications” pages for the

minimum clearance requirements of the freezers.

DO NOT

obstruct air intake and discharge openings.

If provided, install the deflector to prevent recirculation

of warm air.

Failure to allow proper clearance and airflow may

cause poor freezer performance and damage to the

machine.

For Indoor Use Only:

This unit is designed to operate

indoors, under normal ambient temperatures of 70

F (21

- 24

C). The freezer has successfully

performed in high ambient temperatures of 104

(40

C) at reduced capacities.

This unit must

NOT

be installed in an area

where a water jet or hose can be used.

NEVER

use a

water jet or hose to rinse or clean this unit. Using a

water jet or hose on or around this equipment may

result in electrocution to the user or damage to the

equipment.

This unit must be installed on a level surface

to avoid the hazard of tipping. Extreme care should be

taken in moving this equipment for any reason.

Two or more people are required to safely move this

unit. Failure to comply may result in personal injury or

equipment damage.

Uncrate the machine. Inspect the unit for damage.

Report any damage to the Taylor factory immediately.

This piece of equipment is made in the USA and has

USA sizes of hardware. All metric conversions are

approximate and vary in size.

Installer Safety

In all areas of the world, equipment should be

installed in accordance with existing local codes.

Please contact your local authorities if you have any

questions.

Care should be taken to ensure that all basic safety

practices are followed during the installation and

servicing activities related to the installation and

service of Taylor equipment.

Only authorized Taylor service personnel
should perform installation and repairs on
the equipment.

Authorized service personnel should consult
OSHA Standard 29CFRI910.147 or the

applicable code of the local area for the
industry standards on lockout/tagout
procedures before beginning any installation
or repairs.

Authorized service personnel must ensure
that the proper PPE is available and worn
when required during installation and

service.

Authorized service personnel must remove
all metal jewelry, rings, and watches before
working on electrical equipment.

THIS UNIT HAS MANY SHARP EDGES

THAT CAN CAUSE SEVERE INJURIES.

Examples:

scraper blades

condenser fins

Содержание Taylormate 150














































































Результаты поиска

Содержание Taylormate 150

Отзывы:

Похожие инструкции для Taylormate 150

Бренды по названию

Популярные бренды

Taylor Taylormate 150, Руководство по обслуживанию

Результаты поиска

Содержание Taylormate 150

Отзывы:

Похожие инструкции для Taylormate 150

Бренды по названию

Популярные бренды